Technician Question Pool

All 409 questions, word for word, with the answer and an explanation for each. In use from July 1, 2026 to June 30, 2030.

Technician exam guide

T1 Commission’s Rules

T1A Purpose and permissible use of the Amateur Radio Service; Operator/primary station license grant; Meanings of basic terms used in FCC rules; Interference; RACES rules; Phonetics; Frequency Coordinator; Beacon

  1. T1A01 Which of the following is part of the Basis and Purpose of the Amateur Radio Service?
  2. T1A02 Which agency regulates and enforces the rules for the Amateur Radio Service in the United States?
  3. T1A03 What do the FCC rules state regarding the use of a phonetic alphabet for station identification in the Amateur Radio Service?
  4. T1A04 How do you receive official notification of your new license and call sign after passing the exam?
  5. T1A05 What proves that the FCC has issued an operator/primary license grant?
  6. T1A06 On which of the following HF frequencies can automatically controlled amateur propagation beacons be found?
  7. T1A07 What is the FCC Part 97 definition of a space station?
  8. T1A08 Who recommends transmit/receive channels for repeater and auxiliary stations?
  9. T1A09 Who selects a Frequency Coordinator?
  10. T1A10 Besides an FCC-issued amateur operator license, what is required to be the control operator of a Radio Amateur Civil Emergency Service (RACES) Station?
  11. T1A11 Which of the following is prohibited?

T1B Frequency allocations; Emission modes; Spectrum sharing; Transmissions near band edges; Contacting the International Space Station; Power output

  1. T1B01 Which of the following frequency ranges are available for phone operation by Technician licensees?
  2. T1B02 Which of the following U.S. amateur radio operators are allowed to contact the International Space Station (ISS) on VHF bands?
  3. T1B03 Which frequency is in the 6-meter amateur band?
  4. T1B04 Which amateur band includes 146.52 MHz?
  5. T1B05 Which of the following bands include frequencies where Technicians are authorized to use digital modes such as FT8?
  6. T1B06 On which HF bands does a Technician class operator have phone privileges?
  7. T1B07 Which of the following VHF/UHF band segments are limited to CW only?
  8. T1B08 How are US amateurs restricted in segments of bands where the Amateur Radio Service is secondary?
  9. T1B09 Why should you not set your transmit frequency to be exactly at the edge of an amateur band or sub-band?
  10. T1B10 Where may SSB phone be used in amateur bands above 50 MHz?
  11. T1B11 What is the maximum peak envelope power output for Technician class operators in their HF band segments?
  12. T1B12 Except for some specific restrictions, what is the maximum peak envelope power output for Technician class operators using frequencies above 30 MHz?

T1C Licensing: classes, sequential and vanity call sign systems, places where the Amateur Radio Service is regulated by the FCC, name and address on FCC license database, term, renewal, grace period, maintaining mailing address; International communications

  1. T1C01 For which classes of amateur radio licenses does the FCC currently issue new licenses?
  2. T1C02 Who may select a desired call sign under the vanity call sign rules?
  3. T1C03 What types of international communications are FCC-licensed amateur radio stations permitted to make?
  4. T1C04 What may happen if the FCC is unable to reach you by email?
  5. T1C05 Which of the following is a valid Group D call sign format for Technician class?
  6. T1C06 Which of the following statements is true about using your amateur radio license when operating aboard a vessel or craft in international waters?
  7. T1C07 How long before the expiration date may an amateur radio license renewal be requested?
  8. T1C08 What is the normal term for an FCC-issued amateur radio license?
  9. T1C09 What is the grace period for renewal if an amateur license expires?
  10. T1C10 How soon after passing the examination for your first amateur radio license may you transmit on the amateur radio bands?
  11. T1C11 If your license has expired and is still within the allowable grace period, may you continue to transmit on the amateur radio bands?

T1D Authorized and prohibited transmissions; Sale of equipment

  1. T1D01 With which countries are FCC-licensed amateur radio stations prohibited from exchanging communications?
  2. T1D02 Under which of the following circumstances are one-way transmissions by an amateur station prohibited?
  3. T1D03 When is it permissible to transmit messages encoded to obscure their meaning?
  4. T1D04 Under what conditions is an amateur station authorized to transmit music using a phone emission?
  5. T1D05 When may amateur radio operators use their stations to notify other amateurs of the availability of equipment for sale or trade?
  6. T1D06 What, if any, are the restrictions concerning transmission of language that may be considered indecent or obscene?
  7. T1D07 Which of the following is an example of an auxiliary station?
  8. T1D08 In which of the following circumstances may the control operator of an amateur station receive compensation for operating that station?
  9. T1D09 When may amateur stations transmit information in support of broadcasting, program production, or news gathering, assuming no other means is available?
  10. T1D10 How does the FCC define broadcasting for the Amateur Radio Service?
  11. T1D11 When may an amateur station transmit without identifying on the air?
  12. T1D12 Which of the following is required when making on-the-air test transmissions?

T1E Control operator: eligibility, designating, privileges, duties, location, required; Control point; Control types: automatic, remote

  1. T1E01 When may an amateur station transmit without a control operator?
  2. T1E02 Who may be the control operator of a station communicating through an amateur satellite or space station?
  3. T1E03 Who must designate the station control operator?
  4. T1E04 What determines the transmitting frequency privileges of an amateur station?
  5. T1E05 What is an amateur station’s control point?
  6. T1E06 When, other than during an emergency, may a Technician class licensee be the control operator of a station operating in an Amateur Extra Class band segment?
  7. T1E07 When the control operator is not the station licensee, who is responsible for the proper operation of the station?
  8. T1E08 Which of the following is an example of automatic control?
  9. T1E09 Which amateur stations may be remotely controlled?
  10. T1E10 Which of the following is an example of remote control as defined in Part 97?
  11. T1E11 What is a control operator as defined in Part 97?

T1F Station identification; Repeaters; Third party communications; Club stations; FCC inspection

  1. T1F01 When must the station licensee make the station and the station records available for inspection?
  2. T1F02 How often must you identify with your FCC-assigned call sign when using tactical call signs such as “Race Headquarters”?
  3. T1F03 When are you required to transmit your assigned call sign?
  4. T1F04 What language must you use for identification when using a phone emission?
  5. T1F05 What method of call sign identification is required for a station transmitting phone signals?
  6. T1F06 Which of the following self-assigned indicators are acceptable when using a phone transmission?
  7. T1F07 Which of the following restrictions apply when a non-licensed person speaks to a foreign amateur radio station via a station under the control of an FCC-licensed amateur radio operator?
  8. T1F08 What is the definition of third-party communications?
  9. T1F09 What type of amateur station simultaneously retransmits the signal of another amateur station on a different channel or channels?
  10. T1F10 Who is accountable if a repeater inadvertently retransmits communications that violate the FCC rules?
  11. T1F11 Which of the following is a requirement for the issuance of a club station license grant?

T2 Operating Procedures

T2A Station operation: choosing an operating frequency, calling another station, test transmissions; Band plans: calling frequencies, repeater offsets

  1. T2A01 What is a common repeater frequency offset in the 2-meter band?
  2. T2A02 What is the national calling frequency for FM simplex operations in the 2-meter band?
  3. T2A03 What is a common repeater frequency offset in the 70-centimeter band?
  4. T2A04 What is an appropriate way to call another station on a repeater if you know the other station's call sign?
  5. T2A05 How should you respond to a station calling CQ?
  6. T2A06 What is an effective way to seek a call from any phone station when not using a repeater?
  7. T2A07 What does the term "repeater offset" mean?
  8. T2A08 What is the meaning of the procedural signal “CQ”?
  9. T2A09 Which of the following is a customary way to indicate a station is listening on a repeater and looking for a contact?
  10. T2A10 What is a band plan, beyond the privileges established by the FCC?
  11. T2A11 What term describes an amateur station that is transmitting and receiving on the same frequency?

T2B VHF/UHF operating practices: FM repeater, simplex, reverse splits; Access tones: CTCSS, DTMF; DMR operation; Resolving operating problems; Q signals

  1. T2B01 What is the purpose of the reverse function on a VHF/UHF transceiver?
  2. T2B02 What term describes the use of a sub-audible tone transmitted along with normal voice audio to open the squelch of a receiver?
  3. T2B03 Which of the following describes a linked repeater network?
  4. T2B04 Which of the following could be the reason you are unable to access a repeater whose output you can hear?
  5. T2B05 Which of the following would cause your FM transmission audio to drop out on voice peaks?
  6. T2B06 What type of signaling to a repeater uses two simultaneous audio tones?
  7. T2B07 How can you join a digital repeater’s “talkgroup”?
  8. T2B08 Which of the following applies when two stations transmitting on the same frequency interfere with each other?
  9. T2B09 Why are simplex channels designated in the VHF/UHF band plans?
  10. T2B10 Which Q signal indicates that you are receiving interference from other stations?
  11. T2B11 Which Q signal indicates that you are changing frequency?
  12. T2B12 What is the digital color code used on DMR repeater systems?
  13. T2B13 What is the purpose of a squelch function?
  14. T2B14 Which of the following is a “talkgroup”?

T2C Public service: emergency operations, applicability of FCC rules, RACES and ARES, net and traffic procedures, operating restrictions during emergencies, use of phonetics in message handling

  1. T2C01 When do the FCC Part 97 Amateur Radio Service rules NOT apply to the operation of an amateur station?
  2. T2C02 Which of the following are typical duties of a Net Control Station?
  3. T2C03 What technique is used to ensure that voice messages containing unusual words are received correctly?
  4. T2C04 What is RACES?
  5. T2C05 What does the term “traffic” refer to in net operation?
  6. T2C06 What is the Amateur Radio Emergency Service (ARES)?
  7. T2C07 Which of the following is standard practice when you participate in a net?
  8. T2C08 Which of the following relays messages using email addresses based on amateur callsigns?
  9. T2C09 Are amateur station control operators ever permitted to operate outside the frequency privileges of their license class?
  10. T2C10 What information is contained in the preamble of a formal traffic message?
  11. T2C11 What is meant by “check” in a radiogram header?
  12. T2C12 Which of the following requires certification by a civil defense agency?

T3 Radio Wave Propagation

T3A Radio wave characteristics: how a radio signal travels, fading, multipath, polarization, wavelength vs absorption; Antenna orientation

  1. T3A01 Why do VHF signal strengths sometimes vary greatly when the antenna is moved only a few feet?
  2. T3A02 How does vegetation affect UHF and microwave signals?
  3. T3A03 What antenna polarization is normally used for long-distance CW and SSB contacts on the VHF and UHF bands?
  4. T3A04 What is the effect of antenna cross-polarization over a line-of-sight VHF or UHF path?
  5. T3A05 When using a directional antenna, how might your station be able to communicate with a distant repeater if buildings or obstructions are blocking the direct line of sight path?
  6. T3A06 What is the meaning of the term “picket fencing”?
  7. T3A07 What weather condition might decrease range at microwave frequencies?
  8. T3A08 What is a likely cause of irregular fading of signals propagated by the ionosphere?
  9. T3A09 Which of the following results from the fact that signals propagated by the ionosphere are elliptically polarized?
  10. T3A10 What effect does multi-path propagation have on data transmissions?
  11. T3A11 Which region of the atmosphere can reflect HF radio waves?
  12. T3A12 What effect does fog or rain have on 10-meter and 6-meter band signals?

T3B Electromagnetic wave properties: wavelength vs frequency, nature and velocity of electromagnetic waves, relationship of wavelength and frequency; Electromagnetic spectrum definitions: UHF, VHF, HF

  1. T3B01 What is the relationship between the electric and magnetic fields of an electromagnetic wave?
  2. T3B02 What property of a radio wave defines its polarization?
  3. T3B03 What are the two components of a radio wave?
  4. T3B04 What is the velocity of a radio wave traveling through free space?
  5. T3B05 What is the relationship between wavelength and frequency?
  6. T3B06 What is the formula for converting frequency to approximate wavelength in meters?
  7. T3B07 In addition to frequency, which of the following is used to identify amateur radio bands?
  8. T3B08 What frequency range is referred to as VHF?
  9. T3B09 What frequency range is referred to as UHF?
  10. T3B10 What frequency range is referred to as HF?
  11. T3B11 What is the approximate velocity of a radio wave in free space?
  12. T3B12 Which of these frequencies travels at the highest velocity in free space?

T3C Propagation modes: sporadic E, meteor scatter, auroral propagation, tropospheric ducting; F region skip; Line of sight and radio horizon

  1. T3C01 Why are simplex UHF signals rarely heard beyond their radio horizon?
  2. T3C02 What is a characteristic of HF communication compared with communications on VHF and higher frequencies?
  3. T3C03 What is one characteristic of VHF signals received via auroral backscatter?
  4. T3C04 Which of the following types of propagation is most commonly associated with occasional strong signals on the 10-, 6-, and 2-meter bands from beyond the radio horizon?
  5. T3C05 Which of the following effects may allow radio signals to travel beyond obstructions between the transmitting and receiving stations?
  6. T3C06 What type of propagation is responsible for allowing over-the-horizon VHF and UHF communications to ranges of approximately 300 miles on a regular basis?
  7. T3C07 What band is best suited for communicating via meteor scatter?
  8. T3C08 What causes tropospheric ducting?
  9. T3C09 What is generally the best time for long-distance 10-meter band propagation via the F region?
  10. T3C10 Which of the following bands may provide long-distance communications via the ionosphere’s F region during the peak of the sunspot cycle?
  11. T3C11 Why is the radio horizon for VHF and UHF signals more distant than the visual horizon?

T4 Amateur Radio Practices

T4A Station setup: connecting a microphone, RF power meter, a power source, a computer, digital equipment, an SWR meter; bonding; Mobile radio installation

  1. T4A01 Which of the following is an appropriate power supply rating for a typical 50-watt output mobile FM transceiver?
  2. T4A02 Which of the following should be considered when selecting an accessory SWR meter?
  3. T4A03 Why are short, heavy-gauge wires used for a transceiver’s DC power connection?
  4. T4A04 How are the audio input and output of a transceiver connected in a station configured to operate using FT8?
  5. T4A05 Where should an RF power meter be installed?
  6. T4A06 What signals are used in a computer-radio interface for digital mode operation?
  7. T4A07 Which of the following is one of the connections required between a computer and a transceiver to operate digital modes?
  8. T4A08 Which of the following conductors is preferred for bonding at RF?
  9. T4A09 How can you determine the length of time that equipment can be powered from a battery?
  10. T4A10 What function does a digital mode hotspot perform for nearby transceivers?
  11. T4A11 Where should the negative power return of a mobile transceiver be connected in a vehicle?
  12. T4A12 What is an electronic keyer?

T4B Operating controls: frequency tuning, use of filters, squelch function, AGC, memory channels, noise blanker, microphone gain, receiver incremental tuning (RIT), bandwidth selection, scanning function; Digital transceiver configuration; DMR code plugs and talk groups

  1. T4B01 What is the effect of excessive microphone gain on SSB transmissions?
  2. T4B02 Which of the following can be used to enter a transceiver’s operating frequency?
  3. T4B03 How is squelch adjusted so that a weak FM signal can be heard?
  4. T4B04 What does an FM signal sound like when received slightly off frequency?
  5. T4B05 What does the scanning function of an FM transceiver do?
  6. T4B06 Which of the following controls could be used if the voice pitch of a single-sideband signal returning to your CQ call seems too high or low?
  7. T4B07 What is a DMR “code plug”?
  8. T4B08 What is the advantage of having a choice of receiver filter bandwidths in a multimode transceiver?
  9. T4B09 How is a specific group of stations selected on a DMR digital voice transceiver?
  10. T4B10 Which of the following receiver filter bandwidths provides the best signal-to-noise ratio for SSB reception?
  11. T4B11 Which of the following must be programmed into a D-STAR digital transceiver before transmitting?

T5 Electrical Principles

T5A Current and voltage: terminology and units, conductors and insulators, alternating and direct current

  1. T5A01 Electrical current is measured in which of the following units?
  2. T5A02 Electrical power is measured in which of the following units?
  3. T5A03 What is the term for the flow of electrons in an electric circuit?
  4. T5A04 What term describes the number of times per second that an alternating current makes a complete cycle?
  5. T5A05 A difference in which of the following causes electron flow?
  6. T5A06 What is the unit of frequency?
  7. T5A07 Why are metals generally good conductors of electricity?
  8. T5A08 Which of the following is a good electrical insulator?
  9. T5A09 Which of the following describes alternating current?
  10. T5A10 Which term describes the rate at which electrical energy is used?
  11. T5A11 What type of current flow is opposed by resistance?

T5B Math for electronics: conversion of electrical units, decibels

  1. T5B01 How many milliamperes is 1.5 amperes?
  2. T5B02 Which is equal to 1,500,000 hertz?
  3. T5B03 Which is equal to one kilovolt?
  4. T5B04 Which is equal to one microvolt?
  5. T5B05 Which is equal to 500 milliwatts?
  6. T5B06 Which is equal to 3000 milliamperes?
  7. T5B07 Which is equal to 3.525 MHz?
  8. T5B08 Which is equal to 1,000,000 picofarads?
  9. T5B09 Which decibel value most closely represents a power increase from 5 watts to 10 watts?
  10. T5B10 Which decibel value most closely represents a power decrease from 12 watts to 3 watts?
  11. T5B11 Which decibel value represents a power increase from 20 watts to 200 watts?
  12. T5B12 Which is equal to 28400 kHz?
  13. T5B13 Which is equal to 2425 MHz?

T5C Capacitance and inductance terminology and units; Radio frequency definition and units; Impedance definition and units; Calculating power

  1. T5C01 What describes the ability to store energy in an electric field?
  2. T5C02 What is the unit of capacitance?
  3. T5C03 What describes the ability to store energy in a magnetic field?
  4. T5C04 What is the unit of inductance?
  5. T5C05 What is the unit of impedance?
  6. T5C06 What is the abbreviation for kilohertz?
  7. T5C07 What is the abbreviation for megahertz?
  8. T5C08 What formula is used to calculate electrical power (P) in a DC circuit?
  9. T5C09 How much power is delivered by a voltage of 13.8 volts DC and a current of 10 amperes?
  10. T5C10 How much power is delivered by a voltage of 12 volts DC and a current of 2.5 amperes?
  11. T5C11 How much current is required to deliver 120 watts at a voltage of 12 volts DC?
  12. T5C12 What is impedance?

T5D Ohm’s Law; Series and parallel circuits

  1. T5D01 What formula is used to calculate current in a circuit?
  2. T5D02 What formula is used to calculate voltage in a circuit?
  3. T5D03 What formula is used to calculate resistance in a circuit?
  4. T5D04 What is the resistance of a circuit in which a current of 3 amperes flows when connected to 90 volts?
  5. T5D05 What is the resistance of a circuit for which the applied voltage is 12 volts and the current flow is 1.5 amperes?
  6. T5D06 What is the resistance of a circuit that draws 4 amperes from a 12-volt source?
  7. T5D07 What is the current in a circuit with an applied voltage of 120 volts and a resistance of 80 ohms?
  8. T5D08 What is the current through a 100-ohm resistor connected across 200 volts?
  9. T5D09 What is the current through a 24-ohm resistor connected across 240 volts?
  10. T5D10 What is the voltage across a 2-ohm resistor if a current of 0.5 amperes flows through it?
  11. T5D11 What is the voltage across a 10-ohm resistor if a current of 1 ampere flows through it?
  12. T5D12 What is the voltage across a 10-ohm resistor if a current of 2 amperes flows through it?
  13. T5D13 In which type of circuit is the current always the same through all components?
  14. T5D14 In which type of circuit is the voltage always the same across all components?

T6 Electronic and Electrical Components

T6A Fixed and variable resistors; Capacitors; Inductors; Fuses; Switches; Batteries

  1. T6A01 What electrical component opposes the flow of current in a DC circuit?
  2. T6A02 What type of component is often used as an adjustable volume control?
  3. T6A03 What electrical parameter is controlled by a potentiometer?
  4. T6A04 What electrical component stores energy in an electric field?
  5. T6A05 What type of electrical component consists of conductive surfaces separated by an insulator?
  6. T6A06 What type of electrical component stores energy in a magnetic field?
  7. T6A07 What electrical component is typically constructed as a coil of wire?
  8. T6A08 What is the function of an SPDT switch?
  9. T6A09 What type of switch is represented by component 3 in figure T-2?
  10. T6A10 Which of the following battery chemistries is rechargeable?
  11. T6A11 Which of the following battery chemistries is not rechargeable?

T6B Semiconductors: basic principles and applications of solid-state devices, diodes and transistors; Gain

  1. T6B01 Which is true about forward voltage drop in a diode?
  2. T6B02 What electronic component allows current to flow in only one direction?
  3. T6B03 Which of these components can be used as an electronic switch?
  4. T6B04 Which of the following components can consist of three regions of semiconductor material?
  5. T6B05 What type of transistor has a gate, drain, and source?
  6. T6B06 How is the cathode lead of a semiconductor diode often marked on the package?
  7. T6B07 What causes a light-emitting diode (LED) to emit light?
  8. T6B08 What does the abbreviation FET stand for?
  9. T6B09 What are the names for the electrodes of a diode?
  10. T6B10 Which of the following can provide power gain?
  11. T6B11 What does the term gain mean in amplifiers?
  12. T6B12 What are the names of the electrodes of a bipolar junction transistor?

T6C Circuit diagrams: use of schematics, basic structure; Schematic symbols of basic components

  1. T6C01 What is an electrical diagram using standard component symbols called?
  2. T6C02 What is component 1 in figure T-1?
  3. T6C03 What is component 2 in figure T-1?
  4. T6C04 What is component 3 in figure T-1?
  5. T6C05 What is component 4 in figure T-1?
  6. T6C06 What is component 6 in figure T-2?
  7. T6C07 What is component 8 in figure T-2?
  8. T6C08 What is component 9 in figure T-2?
  9. T6C09 What is component 4 in figure T-2?
  10. T6C10 What is component 3 in figure T-3?
  11. T6C11 What is component 4 in figure T-3?
  12. T6C12 Which of the following is accurately represented in electrical schematics?

T6D Component functions: rectifiers, relays, voltage regulators, meters, indicators, integrated circuits, transformers; Resonant circuit; Shielding

  1. T6D01 Which of the following devices or circuits changes an alternating current into a varying direct current signal?
  2. T6D02 What is a relay?
  3. T6D03 Which of the following is a reason to use shielded wire?
  4. T6D04 Which of the following displays an electrical quantity as a numeric value?
  5. T6D05 What type of circuit controls the amount of voltage from a power supply?
  6. T6D06 What component changes 120 V AC power to a lower AC voltage for other uses?
  7. T6D07 Which of the following is commonly used as a visual indicator?
  8. T6D08 Which of the following is combined with an inductor to make a resonant circuit?
  9. T6D09 What is the name of a device that combines several semiconductors and other components into one package?
  10. T6D10 What is the function of component 2 in figure T-1?
  11. T6D11 Which of the following is a resonant or tuned circuit?

T7 Practical Circuits

T7A Station equipment: receivers, transceivers, transmitter amplifiers, RF preamplifiers, transverters; Basic radio circuit concepts and terminology: sensitivity, selectivity, mixers, oscillators, Push-To-Talk (PTT), VFO, modulation

  1. T7A01 Which term describes the ability of a receiver to detect the presence of a signal?
  2. T7A02 What is a transceiver?
  3. T7A03 Which of the following is used to convert a signal from one frequency to another?
  4. T7A04 Which term describes the ability of a receiver to discriminate between multiple signals?
  5. T7A05 What is the name of a circuit that generates a signal at a specific frequency?
  6. T7A06 What device converts the RF input and output of a transceiver to another band?
  7. T7A07 What is the function of a transceiver’s PTT input?
  8. T7A08 Which of the following describes combining speech with an RF carrier signal?
  9. T7A09 What is the function of the switch which selects either SSB or CW-FM on some VHF power amplifiers?
  10. T7A10 What can be added to the output of a transceiver to increase the transmitted output power?
  11. T7A11 What is the function of the Variable Frequency Oscillator (VFO) circuit in a transceiver?

T7B Symptoms, causes, and cures of common transmitter and receiver problems: overload and overdrive, distortion, interference and consumer electronics, RF feedback

  1. T7B01 What can you do if you are told your FM handheld or mobile transceiver is over-deviating?
  2. T7B02 What would cause a broadcast AM or FM radio to receive an amateur radio transmission unintentionally?
  3. T7B03 Which of the following can cause radio frequency interference?
  4. T7B04 Which of the following might be the cause of low RF power output from a solid-state transceiver?
  5. T7B05 Which of the following might reduce interference by an amateur station to a non-amateur over-the-air radio receiver?
  6. T7B06 Which of the following actions should you take if a neighbor tells you that your station’s transmissions are interfering with their radio or TV reception?
  7. T7B07 Which of the following can reduce interference to a 2-meter band transceiver from a nearby commercial FM station?
  8. T7B08 What should you do if something in a neighbor’s home is causing harmful interference to your amateur station?
  9. T7B09 What should be the first step to resolve non-fiber optic cable TV interference caused by your amateur radio transmission?
  10. T7B10 What might be a problem if you receive a report that your audio signal through an FM repeater is distorted or unintelligible?
  11. T7B11 Which of the following can eliminate distorted voice transmissions?

T7C Antenna and transmission line measurements and troubleshooting: measuring SWR, effects of high SWR, causes of feed line failures; Basic coaxial cable characteristics; Use of dummy loads when testing

  1. T7C01 What is the primary purpose of a dummy load?
  2. T7C02 Which of the following is used to determine if an antenna is resonant at the desired operating frequency?
  3. T7C03 What does a typical RF dummy load consist of?
  4. T7C04 What reading on an SWR meter indicates a perfect impedance match between the antenna and the feed line?
  5. T7C05 Why do most solid-state transmitters reduce output power as SWR increases beyond a certain level?
  6. T7C06 What does an SWR reading of 4:1 indicate?
  7. T7C07 What happens to power lost in a feed line?
  8. T7C08 Which instrument can be used to determine SWR?
  9. T7C09 Which of the following causes failure of coaxial cables?
  10. T7C10 Why should the outer jacket of coaxial cable be resistant to ultraviolet light?
  11. T7C11 What is an advantage of foam-dielectric versus solid-dielectric coaxial cable?

T7D Using basic test instruments: voltmeter, ammeter, and ohmmeter; Soldering

  1. T7D01 Which instrument would you use to measure electric potential?
  2. T7D02 How is a voltmeter connected to a component to measure applied voltage?
  3. T7D03 When configured to measure current, how is a multimeter connected to a component?
  4. T7D04 Which instrument is used to measure electric current?
  5. T7D05 How does an ohmmeter measure the resistance of a circuit or component?
  6. T7D06 Which of the following can damage a multimeter?
  7. T7D07 Which of the following measurements are made using a multimeter?
  8. T7D08 Which of the following types of solder should not be used for radio and electronic applications?
  9. T7D09 What is the characteristic appearance of a cold tin-lead solder joint?
  10. T7D10 What reading indicates that an ohmmeter is connected across a large, discharged capacitor?
  11. T7D11 Which of the following precautions should be taken when measuring in-circuit resistance with an ohmmeter?

T8 Signals and Emissions

T8A Basic characteristics of FM and SSB; Bandwidth of various modulation modes: CW, SSB, FM, fast-scan TV; Choice of emission type: selection of USB vs LSB, use of SSB for weak signal work, use of FM for VHF packet and repeaters

  1. T8A01 Which of the following is a form of amplitude modulation?
  2. T8A02 What type of modulation is commonly used for VHF packet radio transmissions?
  3. T8A03 Which type of voice mode is often used for long-distance (weak signal) contacts on the VHF and UHF bands?
  4. T8A04 Which type of modulation is commonly used for VHF and UHF voice repeaters?
  5. T8A05 Which of the following signal types has the narrowest bandwidth?
  6. T8A06 Which sideband is normally used for 10-meter HF, VHF, and UHF single-sideband communications?
  7. T8A07 What is one characteristic of single sideband (SSB) compared to FM?
  8. T8A08 What is the approximate bandwidth of a typical single sideband (SSB) voice signal?
  9. T8A09 What is the approximate bandwidth of an FM voice signal on VHF repeaters?
  10. T8A10 What is the approximate bandwidth of AM fast-scan TV transmissions?
  11. T8A11 What is the approximate bandwidth required to transmit a CW signal?
  12. T8A12 Which of the following is a disadvantage of FM compared with single sideband?

T8B Amateur satellite operation: Doppler shift, basic orbits, operating protocols, modulation mode selection, transmitter power considerations, telemetry, satellite tracking programs, beacons, uplink and downlink mode definitions, spin fading, definition of “LEO”, setting uplink power

  1. T8B01 What telemetry information is typically transmitted by satellite beacons?
  2. T8B02 What is the impact of using excessive effective radiated power on a satellite uplink?
  3. T8B03 Which of the following are provided by satellite tracking programs?
  4. T8B04 What mode of transmission is commonly used by amateur radio satellites?
  5. T8B05 What is a satellite beacon?
  6. T8B06 Which of the following are inputs to a satellite tracking program?
  7. T8B07 What is Doppler shift in reference to satellite communications?
  8. T8B08 What does it mean if a satellite is operating in U/V mode?
  9. T8B09 What causes spin fading of satellite signals?
  10. T8B10 What does the term LEO mean in reference to communication satellites?
  11. T8B11 Who is permitted to receive telemetry from an amateur radio satellite?
  12. T8B12 Which of the following is a way to determine whether your satellite uplink power into a linear transponder satellite is neither too low nor too high?

T8C Operating activities: radio direction finding, contests, linking over the internet, exchanging grid locators

  1. T8C01 Which of the following methods is used to locate sources of noise interference or jamming?
  2. T8C02 Which of these items would be useful for a hidden transmitter hunt?
  3. T8C03 What operating activity involves contacting as many stations as possible during a specified period?
  4. T8C04 Which of the following is good practice when contacting another station in a contest?
  5. T8C05 What is a grid locator?
  6. T8C06 How is over the air access to Internet Radio Linking Project (IRLP) nodes accomplished?
  7. T8C07 What is Voice Over Internet Protocol (VoIP)?
  8. T8C08 What is the Internet Radio Linking Project (IRLP)?
  9. T8C09 Which of the following protocols enables an amateur station to transmit through a repeater without using a radio to initiate the transmission?
  10. T8C10 What is required before using the EchoLink system?
  11. T8C11 What is an amateur radio station that connects other amateur stations to the internet?

T8D Non-voice and digital communications: image signals and definition of NTSC, CW, packet radio, PSK, APRS, error detection and correction, amateur radio networking, DMR, WSJT modes, Broadband-Hamnet

  1. T8D01 Which of the following is a digital communications mode?
  2. T8D02 What is FT8?
  3. T8D03 What kind of data can be transmitted by APRS?
  4. T8D04 What is meant by the term "NTSC?"
  5. T8D05 Which of the following is an application of APRS?
  6. T8D06 What does the abbreviation "PSK" mean?
  7. T8D07 Which of the following describes DMR?
  8. T8D08 Which of the following is included in packet radio transmissions?
  9. T8D09 What is CW?
  10. T8D10 Which of the following operating activities is supported by digital mode software in the WSJT-X software suite?
  11. T8D11 What is the role of ARQ in a transmission system?
  12. T8D12 Which of the following best describes an amateur radio mesh network?

T9 Antennas and Feed Lines

T9A Antennas: vertical and horizontal polarization, concept of antenna gain, definition and types of beam antennas, antenna loading, common portable and mobile antennas, relationships between resonant length and frequency, dipole pattern

  1. T9A01 What is a beam antenna?
  2. T9A02 Which of the following describes a type of antenna loading?
  3. T9A03 How is the polarization of an antenna described?
  4. T9A04 What is a disadvantage of a handheld radio transceiver’s short flexible antenna compared to a full-sized quarter-wave antenna?
  5. T9A05 Which of the following increases the resonant frequency of a dipole antenna?
  6. T9A06 Which of the following types of antennas offers the greatest gain?
  7. T9A07 What is a potential drawback of using a handheld VHF transceiver inside a vehicle that lacks an externally mounted antenna?
  8. T9A08 Why is a 19-inch-long vertical antenna often used on 2 meters?
  9. T9A09 What is an advantage of a 5/8-wavelength whip antenna for VHF or UHF mobile service compared to a 1/4-wave antenna?
  10. T9A10 In which direction does a half-wave dipole antenna radiate the strongest signal?
  11. T9A11 What is antenna gain?

T9B Feed lines: types, attenuation vs frequency, selecting; SWR concepts; Antenna tuners (couplers); RF Connectors: selecting, weather protection

  1. T9B01 Which of the following connectors should be carefully taped for weather protection when used outdoors?
  2. T9B02 What is the most common impedance of coaxial cables used in amateur radio?
  3. T9B03 Why is coaxial cable the most common feed line for amateur radio antenna systems?
  4. T9B04 What is the major function of an antenna tuner (antenna coupler)?
  5. T9B05 What happens as the frequency of a signal in coaxial cable is increased?
  6. T9B06 Which of the following connector types is most suitable as an RF connector for frequencies above 400 MHz?
  7. T9B07 Which of the following is true of PL-259 type coax connectors?
  8. T9B08 Which of the following is a source of loss in coaxial feed line?
  9. T9B09 What can cause erratic changes in SWR?
  10. T9B10 What is the electrical difference between RG-58 and RG-213 coaxial cable?
  11. T9B11 Which of the following types of feed line has the lowest loss?
  12. T9B12 What is standing wave ratio (SWR)?

T0 Safety

T0A Power circuits and hazards: hazardous voltages, fuses and circuit breakers, grounding, electrical code compliance; Lightning protection; Battery safety

  1. T0A01 Which of the following is a safety hazard of a 12-volt storage battery that lacks internal protection circuitry?
  2. T0A02 What health hazard is posed by electrical current flowing through the body?
  3. T0A03 In the United States, what circuit does black wire insulation indicate in a three-wire 120 V AC cable?
  4. T0A04 What is the purpose of a fuse in an electrical circuit?
  5. T0A05 Why should a 5-ampere fuse never be replaced with a 20-ampere fuse?
  6. T0A06 What is a good way to guard against electrical shock at your station?
  7. T0A07 Where should a lightning arrester be installed in a coaxial feed line?
  8. T0A08 Where should a fuse or circuit breaker be installed in a 120V AC power circuit?
  9. T0A09 What should be done to all external ground rods or earth connections?
  10. T0A10 What hazard exists when rapidly charging or discharging an unprotected battery?
  11. T0A11 What hazard exists in a power supply immediately after turning it off?
  12. T0A12 Which of the following precautions should be taken when measuring high voltages with a voltmeter?

T0B Antenna safety: tower safety and grounding, installing antennas, antenna supports

  1. T0B01 Which of the following is good practice when installing ground wires on a tower for lightning protection?
  2. T0B02 What is required when climbing an antenna tower?
  3. T0B03 Under what circumstances is it safe to climb a tower without a helper or observer?
  4. T0B04 Which of the following is an important safety precaution to observe when putting up an antenna tower?
  5. T0B05 What is the purpose of a safety wire through a turnbuckle used to tension guy lines?
  6. T0B06 What is the minimum safe distance from a power line to allow when installing an antenna?
  7. T0B07 Which of the following is an important safety rule to remember when using a crank-up tower?
  8. T0B08 Which is a proper grounding method for a tower?
  9. T0B09 Why should you avoid attaching an antenna to a utility pole?
  10. T0B10 Which of the following is true when installing grounding conductors used for lightning protection?
  11. T0B11 Which of the following establishes grounding requirements for an amateur radio tower or antenna?

T0C RF hazards: radiation exposure, proximity to antennas, recognized safe power levels, radiation types, duty cycle

  1. T0C01 What type of radiation are radio signals?
  2. T0C02 Which of the following bands has the lowest maximum permissible exposure for RF safety?
  3. T0C03 How does the allowable power density for RF safety change if duty cycle changes from 100 percent to 50 percent?
  4. T0C04 What factors affect the RF exposure of people near an amateur station antenna?
  5. T0C05 Why do exposure limits vary with frequency?
  6. T0C06 Which of the following is an acceptable method to determine whether your station complies with FCC RF exposure regulations?
  7. T0C07 What hazard is created by touching an antenna during a transmission?
  8. T0C08 Which of the following actions can reduce exposure to RF radiation?
  9. T0C09 How can you make sure your station stays in compliance with RF safety regulations?
  10. T0C10 Why is duty cycle one of the factors used to determine safe RF radiation exposure levels?
  11. T0C11 What is the definition of duty cycle during the averaging time for RF exposure?
  12. T0C12 How does RF radiation differ from ionizing radiation (radioactivity)?
  13. T0C13 Who is responsible for ensuring that no person is exposed to RF energy above the FCC exposure limits?