Element 8 Question Pool
All 300 questions, word for word, with the answer and an explanation for each. In use since June 25, 2009.
C8A RADAR Principles
C8A01 Marine RADAR Systems
- 8-1A1 Choose the most correct statement containing the parameters which control the size of the target echo.
- 8-1A2 Which of the following has NO effect on the maximum range capability?
- 8-1A3 What type of transmitter power is measured over a period of time?
- 8-1A4 What RADAR component controls timing throughout the system?
- 8-1A5 Which of the following components allows the use of a single antenna for both transmitting and receiving?
- 8-1A6 The sweep frequency of a RADAR indicator is determined by what parameter?
C8A02 Distance and Time
- 8-2A1 A radio wave will travel a distance of three nautical miles in:
- 8-2A2 One RADAR mile is how many microseconds?
- 8-2A3 RADAR range is measured by the constant:
- 8-2A4 If a target is 5 miles away, how long does it take for the RADAR echo to be received back at the antenna?
- 8-2A5 How long would it take for a RADAR pulse to travel to a target 10 nautical miles away and return to the RADAR receiver?
- 8-2A6 What is the distance in nautical miles to a target if it takes 308.5 microseconds for the RADAR pulse to travel from the RADAR antenna to the target and back.
C8A03 Frequency and Wavelength
- 8-3A1 Frequencies generally used for marine RADAR are in the ___ part of the radio spectrum.
- 8-3A2 Practical RADAR operation requires the use of microwave frequencies so that:
- 8-3A3 An S-band RADAR operates in which frequency band?
- 8-3A4 A RADAR operating at a frequency of 3 GHz has a wavelength of approximately:
- 8-3A5 The major advantage of an S-band RADAR over an X-band RADAR is:
- 8-3A6 An X band RADAR operates in which frequency band?
C8A04 Power, Pulse Width, PRR
- 8-4A1 A pulse RADAR has a pulse repetition frequency (PRF) of 400 Hz, a pulse width of 1 microsecond, and a peak power of 100 kilowatts. The average power of the RADAR transmitter is:
- 8-4A2 A shipboard RADAR transmitter has a pulse repetition frequency (PRF) of 1,000 Hz, a pulse width of 0.5 microseconds, peak power of 150 KW, and a minimum range of 75 meters. Its duty cycle is:
- 8-4A3 A pulse RADAR transmits a 0.5 microsecond RF pulse with a peak power of 100 kilowatts every 1600 microseconds. This RADAR has:
- 8-4A4 If a RADAR transmitter has a pulse repetition frequency (PRF) of 900 Hz, a pulse width of 0.5 microseconds and a peak power of 15 kilowatts, what is its average power output?
- 8-4A5 What is the average power if the RADAR set has a PRF of 1000 Hz, a pulse width of 1 microsecond, and a peak power rating of 100 kilowatts?
- 8-4A6 8L37 (C) (250) A search RADAR has a pulse width of 1.0 microsecond, a pulse repetition frequency (PRF) of 900 Hz, and an average power of 18 watts. The unit’s peak power is:
C8A05 Range, Pulse Width, PRF
- 8-5A1 For a range of 5 nautical miles, the RADAR pulse repetition frequency should be:
- 8-5A2 For a range of 100 nautical miles, the RADAR pulse repetition frequency should be:
- 8-5A3 The minimum range of a RADAR is determined by:
- 8-5A4 Short range RADARs would most likely transmit:
- 8-5A5 For a range of 30 nautical miles, the RADAR pulse repetition frequency should be:
- 8-5A6 For a range of 10 nautical miles, the RADAR pulse repetition frequency (PRF) should be:
C8A06 Pulse Width - Pulse Repetition Rates
- 8-6A1 If the PRF is 2500 Hz, what is the PRI?
- 8-6A2 If the pulse repetition frequency (PRF) is 2000 Hz, what is the pulse repetition interval (PRI)?
- 8-6A3 The pulse repetition rate (PRR) refers to:
- 8-6A4 If the RADAR unit has a pulse repetition frequency (PRF) of 2000 Hz and a pulse width of 0.05 microseconds, what is the duty cycle?
- 8-6A5 Small targets are best detected by:
- 8-6A6 What is the relationship between pulse repetition rate and pulse width?
C8A07 Components-1
- 8-7A1 What component of a RADAR receiver is represented by block 46 in Fig. 8A1?
- 8-7A2 A basic sample-and-hold circuit contains:
- 8-7A3 When comparing a TTL and a CMOS NAND gate:
- 8-7A4 Silicon crystals:
- 8-7A5 Which is typical current for a silicon crystal used in a RADAR mixer or detector circuit?
- 8-7A6 What component of a RADAR receiver is represented by block 47 in Fig. 8A1?
C8A08 Components-2
- 8-8A1 The basic frequency determining element in a Gunn oscillator is:
- 8-8A2 Which of the following is not a method of analog-to-digital conversion?
- 8-8A3 When comparing TTL and CMOS logic families, which of the following is true:
- 8-8A4 The primary operating frequency of a reflex klystron is controlled by the:
- 8-8A5 A Gunn diode oscillator takes advantage of what effect?
- 8-8A6 Fine adjustments of a reflex klystron are accomplished by:
C8A09 Circuits-1
- 8-9A1 Blocking oscillators operate on the formula of:
- 8-9A2 The block diagram of a typical RADAR system microprocessor is shown in Fig. 8A2. Choose the most correct statement regarding this system.
- 8-9A3 The phantastron circuit is capable of:
- 8-9A4 The block diagram of a typical RADAR system microprocessor is shown in Fig. 8A2. Choose the most correct statement regarding this system.
- 8-9A5 In the Line-Driver/Coax/Line-receiver circuit shown in Fig. 8A3, what component is represented by the blank box marked "X"?
- 8-9A6 Choose the most correct statement:
C8A10 Circuits-2
- 8-10A1 In the circuit shown in Fig. 8A4, U5 pins 1 and 4 are high and both are in the reset state. Assume one clock cycle occurs of Clk A followed by one cycle of Clk B. What are the output states of the two D-type flip flops?
- 8-10A2 If more light strikes the photodiode in Fig. 8A5, there will be:
- 8-10A3 In the circuit shown in Fig. 8A6, which of the following is true?
- 8-10A4 What is the correct value of RS in Fig. 8A7, if the voltage across the LED is 1.9 Volts with 5 Volts applied and If max equals 40 milliamps?
- 8-10A5 The block diagram of a typical RADAR system microprocessor is shown in Fig. 8A2. Choose the most correct statement regarding this system.
- 8-10A6 You are troubleshooting a component on a printed circuit board in a RADAR system while referencing the Truth Table in Fig. 8A8. What kind of integrated circuit is the component?
C8B Transmitting Systems
C8B11 Transmitting Systems
- 8-11B1 The magnetron is used to:
- 8-11B2 The purpose of the modulator is to:
- 8-11B3 Which of the following statements about most modern RADAR transmitter power supplies is false?
- 8-11B4 The purpose of the Pulse Forming Network is to:
- 8-11B5 The purpose of the Synchronizer is to:
- 8-11B6 Which of the following is not part of the transmitting system?
C8B12 Magnetrons
- 8-12B1 High voltage is applied to what element of the magnetron?
- 8-12B2 The characteristic of the magnetron output pulse that relates to accurate range measurement is its:
- 8-12B3 What device is used as a transmitter in a marine RADAR system?
- 8-12B4 The magnetron is:
- 8-12B5 A negative voltage is commonly applied to the magnetron cathode rather than a positive voltage to the magnetron anode because:
- 8-12B6 The anode of a magnetron is normally maintained at ground potential:
C8B13 Modulation
- 8-13B1 In a solid-state RADAR modulator, the duration of the transmitted pulse is determined by:
- 8-13B2 The modulation frequency of most RADAR systems is between:
- 8-13B3 A shipboard RADAR uses a PFN driving a magnetron cathode through a step-up transformer. This results in which type of modulation?
- 8-13B4 In a pulse modulated magnetron what device determines the shape and width of the pulse?
- 8-13B5 What device(s) may act as the modulator of a RADAR system?
- 8-13B6 The purpose of a modulator in the transmitter section of a RADAR is to:
C8B14 Pulse Forming Networks Modulation
- 8-14B1 The pulse developed by the modulator may have an amplitude greater than the supply voltage. This is possible by:
- 8-14B2 Pulse transformers and pulse-forming networks are commonly used to shape the microwave energy burst RADAR transmitter. The switching devices most often used in such pulse-forming circuits are:
- 8-14B3 The purpose of the pulse-forming network is to:
- 8-14B4 The shape and duration of the high-voltage pulse delivered to the magnetron is established by:
- 8-14B5 Pulse-forming networks are usually composed of the following:
- 8-14B6 An artificial transmission line is used for:
C8B15 TR - ATR - Circulators - Directional Couplers-1
- 8-15B1 The ferrite material in a circulator is used as a(an):
- 8-15B2 In a circular resonant cavity with flat ends, the E-field and the H-field form with specific relationships. The:
- 8-15B3 A ferrite circulator is most commonly used in what portion of a RADAR system?
- 8-15B4 A circulator provides what function in the RF section of a RADAR system?
- 8-15B5 A directional coupler has an attenuation of -30 db. A measurement of 100 milliwatts at the coupler indicates the power of the line is:
- 8-15B6 What is the purpose or function of the RADAR duplexer/circulator?
C8B16 TR - ATR - Circulators - Directional Couplers-2
- 8-16B1 The ATR box:
- 8-16B2 When a pulse RADAR is radiating, which elements in the TR box are energized?
- 8-16B3 The TR box:
- 8-16B4 What device is located between the magnetron and the mixer and prevents received signals from entering the magnetron?
- 8-16B5 A keep-alive voltage is applied to:
- 8-16B6 A DC keep-alive potential:
C8B17 Timer - Trigger - Synchronizer Circuits
- 8-17B1 What RADAR circuit determines the pulse repetition rate (PRR)?
- 8-17B2 The triggering section is also known as the:
- 8-17B3 Operation of any RADAR system begins in the:
- 8-17B4 The timer circuit:
- 8-17B5 Pulse RADARs require precise timing for their operation. Which type circuit below might best be used to provide these accurate timing pulses?
- 8-17B6 Unblanking pulses are produced by the timer circuit. Where are they sent?
C8B18 Power Supplies
- 8-18B1 An advantage of resonant charging is that it:
- 8-18B2 The characteristics of a field-effect transistor (FET) used in a modern RADAR switching power supply can be compared as follows:
- 8-18B3 A pulse-width modulator in a switching power supply is used to:
- 8-18B4 In a fixed-frequency switching power supply, the pulse width of the switching circuit will increase when:
- 8-18B5 A major consideration for the use of a switching regulator power supply over a linear regulator is:
- 8-18B6 Which of the following characteristics are true of a power MOSFET used in a RADAR switching supply?
C8C Receiving Systems
C8C19 Receiving Systems
- 8-19C1 Which of the following statements is true?
- 8-19C2 Logarithmic receivers:
- 8-19C3 RADAR receivers are similar to:
- 8-19C4 What section of the receiving system sends signals to the display system?
- 8-19C5 What is the main difference between an analog and a digital receiver?
- 8-19C6 In a RADAR receiver, the RF power amplifier:
C8C20 Mixers
- 8-20C1 The diagram in Fig. 8C9 shows a simplified RADAR mixer circuit using a crystal diode as the first detector. What is the output of the circuit when no echoes are being received?
- 8-20C2 In the receive mode, frequency conversion is generally accomplished by a:
- 8-20C3 An RF mixer has what purpose in a RADAR system?
- 8-20C4 In a RADAR unit, the mixer uses a:
- 8-20C5 What component of a RADAR receiver is represented by block 49 in Fig. 8A1?
- 8-20C6 In a RADAR unit, the mixer uses:
C8C21 Local Oscillators
- 8-21C1 The error voltage from the discriminator is applied to the:
- 8-21C2 In a RADAR unit, the local oscillator is a:
- 8-21C3 What component of a RADAR receiver is represented by block 48 in Fig. 8A1?
- 8-21C4 What device(s) could be used as the local oscillator in a RADAR receiver?
- 8-21C5 The klystron local oscillator is constantly kept on frequency by:
- 8-21C6 How may the frequency of the klystron be varied?
C8C22 Amplifiers
- 8-22C1 Overcoupling in a RADAR receiver will cause?
- 8-22C2 The usual intermediate frequency of a shipboard RADAR unit is:
- 8-22C3 The I.F. Amplifier bandwidth is:
- 8-22C4 A logarithmic IF amplifier is preferable to a linear IF amplifier in a RADAR receiver because it:
- 8-22C5 The high-gain IF amplifiers in a RADAR receiver may amplify a 2 microvolt input signal to an output level of 2 volts. This amount of amplification represents a gain of:
- 8-22C6 In a RADAR receiver AGC and IAGC can vary between:
C8C23 Detectors - Video Amplifiers
- 8-23C1 Which of the following statements is correct?
- 8-23C2 Video amplifiers in pulse RADAR receivers must have a broad bandwidth because:
- 8-23C3 In video amplifiers, compensation for the input and output stage capacitances must be accomplished to prevent distorting the video pulses. This compensation is normally accomplished by connecting:
- 8-23C4 Which of the following signals is not usually an input to the video amplifier?
- 8-23C5 Which of the following signals are usually an input to the video amplifier?
- 8-23C6 The video (second) detector in a pulse modulated RADAR system would most likely use a/an:
C8C24 Automatic Frequency Control - AFC/ATC
- 8-24C1 The AFC system is used to:
- 8-24C2 A circuit used to develop AFC voltage in a RADAR receiver is called the:
- 8-24C3 In the AFC system, the discriminator compares the frequencies of the:
- 8-24C4 An AFC system keeps the receiver tuned to the transmitted signal by varying the frequency of the:
- 8-24C5 A RADAR transmitter is operating on 3.0 GHz and the reflex klystron local oscillator, operating at 3.060 GHz, develops a 60 MHz IF. If the magnetron drifts higher in frequency, the AFC system must cause the klystron repeller plate to become:
- 8-24C6 What component is block 50 in Fig. 8A1?
C8C25 Sea Clutter - STC - FTC
- 8-25C1 The STC circuit is used to:
- 8-25C2 The STC circuit:
- 8-25C3 Sea return is:
- 8-25C4 Sea clutter on the RADAR scope cannot be effectively reduced using front panel controls. What circuit would you suspect is faulty?
- 8-25C5 What circuit controls the suppression of sea clutter?
- 8-25C6 The sensitivity time control (STC) circuit:
C8C26 Power Supplies
- 8-26C1 Prior to making “power-on” measurements on a switching power supply, you should be familiar with the supply because of the following:
- 8-26C2 A constant frequency switching power supply regulator with an input voltage of 165 volts DC, and a switching frequency of 20 kHz, has an “ON” time of 27 microseconds when supplying 1 ampere to its load. What is the output voltage across the load?
- 8-26C3 The circuit shown in Fig. 8C10 is the output of a switching power supply. Measuring from the junction of CR6, CR7 and L1 to ground with an oscilloscope, what waveform would you expect to see?
- 8-26C4 With regard to the comparator shown in Fig. 8C11, the input is a sinusoid. Nominal high level output of the comparator is 4.5 volts. Choose the most correct statement regarding the input and output.
- 8-26C5 When monitoring the gate voltage of a power MOSFET in the switching power supply of a modern RADAR, you would expect to see the gate voltage change from “low” to “high” by how much?
- 8-26C6 The nominal output high of the comparator shown in Fig. 8C11 is 4.5 volts. Choose the most correct statement which describes the trip points.
C8C27 Interference Issues
- 8-27C1 One of the best methods of reducing noise in a RADAR receiver is?
- 8-27C2 The primary cause of noise in a RADAR receiver can be attributed to:
- 8-27C3 Noise can appear on the LCD as:
- 8-27C4 RADAR interference on a communications receiver appears as:
- 8-27C5 In a RADAR receiver the most common types of interference are?
- 8-27C6 Noise can:
C8C28 Miscellaneous
- 8-28C1 The purpose of the discriminator circuit in a RADAR set is to:
- 8-28C2 The MTI circuit:
- 8-28C3 Where is a RF attenuator used in a RADAR unit?
- 8-28C4 The condition known as “glint” refers to a shifting of clutter with each RADAR pulse and can be caused by a:
- 8-28C5 An ion discharge (TR) cell is used to:
- 8-28C6 When the receiver employs an MTI circuit:
C8D Display & Control Systems
C8D29 Displays
- 8-29D1 Modern liquid crystal displays have a pixel count of:
- 8-29D2 Voltages used in CRT anode circuits are in what range of value?
- 8-29D3 The purpose of the aquadag coating on the CRT is:
- 8-29D4 LCD patterns are formed when:
- 8-29D5 In a raster-type display, the electron beam is scanned:
- 8-29D6 Select the statement, which is most correct regarding a raster scan display.
C8D30 Video Amplifiers and Sweep Circuits
- 8-30D1 What are the usual input signals to the video amplifier?
- 8-30D2 Which of the following would not normally be an input to the video amplifier?
- 8-30D3 The purpose of the sweep amplifier is to:
- 8-30D4 How many deflection coils are driven by the sweep amplifier?
- 8-30D5 The main purpose of the sweep generator is to provide:
- 8-30D6 The main purpose of the video amplifier is to provide:
C8D31 Timing Circuits
- 8-31D1 Timing circuits are used to provide what function?
- 8-31D2 The circuit that develops timing signals is called the:
- 8-31D3 Which of the following functions is not affected by the timing circuit?
- 8-31D4 The synchronizer primarily affects the following circuit or function:
- 8-31D5 The output from the synchronizer usually consists of a:
- 8-31D6 The sweep drive is initiated by what circuit?
C8D32 Fixed Range Markers
- 8-32D1 Accurate range markers must be developed using very narrow pulses. A circuit that could be used to provide these high-quality pulses for the CRT is a:
- 8-32D2 Range markers are determined by:
- 8-32D3 A gated LC oscillator, operating at 27 kHz, is being used to develop range markers. If each cycle is converted to a range mark, the range between markers will be:
- 8-32D4 What would be the frequency of a range ring marker oscillator generating range rings at 10 nautical miles intervals?
- 8-32D5 What is the distance between range markers if the controlling oscillator is operating at 20 kHz?
- 8-32D6 What would be the frequency of a range ring marker oscillator generating range rings at intervals of 0.25 nautical miles?
C8D33 Variable Range Markers
- 8-33D1 The variable range marker signal is normally fed to the input of the:
- 8-33D2 The purpose of the variable range marker is to:
- 8-33D3 How is the variable range marker usually adjusted for accuracy?
- 8-33D4 The panel control for the variable range marker is normally a:
- 8-33D5 An important component of the VRM system is the:
- 8-33D6 Which of the following statements about the Variable Range Marker system is correct?
C8D34 EBL, Azimuth and True Bearing
- 8-34D1 The purpose of the Electronic Bearing Line is to:
- 8-34D2 The Electronic Bearing Line is:
- 8-34D3 Which of the following inputs is required to indicate azimuth?
- 8-34D4 Bearing information from the gyro is used to provide the following:
- 8-34D5 Which of the following statements about “true bearing” is correct?
- 8-34D6 A true bearing presentation appears as follows:
C8D35 Memory Systems
- 8-35D1 In a digitized RADAR, the 360 degree sweep is divided into how many digitized segments?
- 8-35D2 While troubleshooting a memory problem in a raster scan RADAR, you discover that the “REFRESH” cycle is not operating correctly. What type of memory circuit are you working on?
- 8-35D3 The term DRAM stands for:
- 8-35D4 How does the dual memory function reduce sea clutter?
- 8-35D5 How many sequential memory cells with target returns are required to display the target?
- 8-35D6 What is the primary purpose of display system memory?
C8D36 ARPA - CAS
- 8-36D1 The ship’s speed indication on the ARPA display can be set manually, but does not change with changes in the vessel’s speed. What other indication would point to a related equipment failure?
- 8-36D2 What does the term ARPA/CAS refer to?
- 8-36D3 Which of the following would not be considered an input to the computer of a collision avoidance system?
- 8-36D4 Which answer best describes a line on the display which indicates a target’s position. The speed is shown by the length of the line and the course by the direction of the line.
- 8-36D5 What is the purpose or function of the “Trial Mode” used in most ARPA equipment?
- 8-36D6 The ARPA term CPA refers to:
C8D37 Display System Power Supplies
- 8-37D1 The display power supply provides the following:
- 8-37D2 The display power supply provides the following:
- 8-37D3 In a display system power supply what is the purpose of the chopper?
- 8-37D4 In a display system power supply, what is the purpose of the inverter?
- 8-37D5 What would be a common switching frequency for a display system power supply?
- 8-37D6 What display system power supply output would use a tripler circuit?
C8D38 Miscellaneous
- 8-38D1 The heading flash is a momentary intensification of the sweep line on the PPI presentation. Its function is to:
- 8-38D2 The major advantage of digitally processing a RADAR signal is:
- 8-38D3 In order to ensure that a practical filter is able to remove undesired components from the output of an analog-to-digital converter, the sampling frequency should be:
- 8-38D4 Bearing resolution is:
- 8-38D5 The output of an RC integrator, when driven by a square wave with a period of much less than one time constant is a:
- 8-38D6 How do you eliminate stationary objects such as trees, buildings, bridges, etc., from the PPI presentation?
C8E Antenna Systems
C8E39 Antenna Systems
- 8-39E1 Slotted waveguide arrays, when fed from one end exhibit:
- 8-39E2 A typical shipboard RADAR antenna is a:
- 8-39E3 Good bearing resolution largely depends upon:
- 8-39E4 The center of the transmitted lobe from a slotted waveguide array is:
- 8-39E5 How does antenna length affect the horizontal beamwidth of the transmitted signal?
- 8-39E6 What is the most common type of RADAR antenna used aboard commercial maritime vessels?
C8E40 Transmission Lines
- 8-40E1 The VSWR of a microwave transmission line device might be measured using:
- 8-40E2 The impedance total (ZO) of a transmission line can be calculated by ZO = √L/C when L and C are known. When a section of transmission line contains 250 microhenries of L and 1000 picofarads of C, its impedance total (ZO) will be:
- 8-40E3 If long-length transmission lines are not properly shielded and terminated:
- 8-40E4 A certain length of transmission line has a characteristic impedance of 72 ohms. If the line is cut at its center, each half of the transmission line will have a ZO of:
- 8-40E5 Standing waves on a transmission line may be an indication that:
- 8-40E6 What precautions should be taken with horizontal waveguide runs?
C8E41 Antenna to Display Interface
- 8-41E1 The position of the PPI scope sweep must indicate the position of the antenna. The sweep and antenna positions are frequently kept in synchronization by the use of:
- 8-41E2 On a basic synchro system, the angular information is carried on the:
- 8-41E3 What is the most common type of antenna position indicating device used in modern RADARs?
- 8-41E4 Which of the following statements about antenna resolvers is correct?
- 8-41E5 An antenna synchro transmitter is composed of the following:
- 8-41E6 RADAR antenna direction must be sent to the display in all ARPAs or RADAR systems. How is this accomplished?
C8E42 Waveguides-1
- 8-42E1 Wave guides can be constructed from:
- 8-42E2 A microwave transmission line constructed of a center conductor suspended between parallel conductive ground planes is called:
- 8-42E3 Wave guide theory is based upon:
- 8-42E4 A waveguide is used at RADAR microwave frequencies because:
- 8-42E5 Wave guide theory is based on the principals of:
- 8-42E6 How is the signal removed from a waveguide or magnetron?
C8E43 Waveguides-2
- 8-43E1 A rotary joint is used to:
- 8-43E2 Resistive losses in a waveguide are very small because:
- 8-43E3 A right-angle bend in an X-band waveguide must have a radius greater than:
- 8-43E4 To insert RF energy into or extract RF energy from a waveguide, which of the following would not be used?
- 8-43E5 The following is true concerning waveguides:
- 8-43E6 At microwave frequencies, waveguides are used instead of conventional coaxial transmission lines because:
C8F Installation, Maintenance & Repair
C8F44 Equipment Faults-1
- 8-44F1 When you examine the RADAR you notice that there is no target video in the center of the CRT. The blank spot gets smaller in diameter as you increase the range scale. What operator front panel control could be misadjusted?
- 8-44F2 Range rings on the PPI indicator are oval in shape. Which circuit would you suspect is faulty?
- 8-44F3 What would be the most likely defective area when there is no target video in the center of the CRT and the blank spot gets smaller in diameter as your range scale is increased?
- 8-44F4 While the vessel is docked the presentation of the pier is distorted near the center of the PPI with the pier appearing to bend in a concave fashion. This is a primary indication of what?
- 8-44F5 In a RADAR using digital video processing, a bright, wide ring appears at a fixed distance from the center of the display on all digital ranges. The transmitter is operating normally. What receiver circuit would you suspect is causing the problem?
- 8-44F6 The raster scan RADAR display has missing video in a rectangular block on the screen. Where is the most likely problem area?
C8F45 Equipment Faults-2
- 8-45F1 A circuit card in a RADAR system has just been replaced with a spare card. You notice the voltage level at point E in Fig. 8F12 is negative 4.75 volts when the inputs are all at 5 volts. The problem is:
- 8-45F2 A defective crystal in the AFC section will cause:
- 8-45F3 The RADAR display has sectors of solid video (spoking). What would be the first thing to check?
- 8-45F4 In the circuit contained in Fig. 8F12, there are 5 volts present at points B and C, and there are zero volts present at points A and D. What is the voltage at point E?
- 8-45F5 If the TR tube malfunctions:
- 8-45F6 The indicated distance from your own vessel to a lighthouse is found to be in error. What circuit would you suspect?
C8F46 Equipment Faults-3
- 8-46F1 Silicon crystals are used in RADAR mixer and detector stages. Using an ohmmeter, how might a crystal be checked to determine if it is functional?
- 8-46F2 In a RADAR unit, if the crystal mixer becomes defective, replace the:
- 8-46F3 An increase in magnetron current that coincides with a decrease in power output is an indication of what?
- 8-46F4 It is reported that the RADAR is not receiving small targets. The most likely causes are:
- 8-46F5 A high magnetron current indicates a/an:
- 8-46F6 Low or no mixer current could be caused by:
C8F47 Equipment Faults-4
- 8-47F1 If the magnetron is allowed to operate without the magnetic field in place:
- 8-47F2 Targets displayed on the RADAR display are not on the same bearing as their visual bearing. What should you first suspect?
- 8-47F3 Loss of distant targets during and immediately after wet weather indicates:
- 8-47F4 In a marine RADAR set, a high VSWR is indicated at the magnetron output. The waveguide and rotary joint appear to be functioning properly. What component may be malfunctioning?
- 8-47F5 On a vessel with two RADARs, one has a different range indication on a specific target than the other. How would you determine which RADAR is incorrect?
- 8-47F6 An increase in the deflection on the magnetron current meter could likely be caused by:
C8F48 Maintenance
- 8-48F1 A thick layer of rust and corrosion on the surface of the parabolic dish will have what effect?
- 8-48F2 The echo box is used for:
- 8-48F3 What should be done to the interior surface of a waveguide in order to minimize signal loss?
- 8-48F4 Which of the following is the most useful instrument for RADAR servicing?
- 8-48F5 A non-magnetic screwdriver should always be used when replacing what component?
- 8-48F6 What kind of display would indicate water in the waveguide?
C8F49 Installation
- 8-49F1 Why is coaxial cable often used for S-band installations instead of a waveguide:
- 8-49F2 RADAR interference to a communications receiver is eliminated by:
- 8-49F3 Why should long horizontal runs of waveguide be avoided?
- 8-49F4 Long horizontal sections of waveguides are not desirable because:
- 8-49F5 In a RADAR system, wave guides should be installed
- 8-49F6 What is the most important factor to consider in locating the antenna?
C8F50 Safety
- 8-50F1 Choose the most correct statement with respect to component damage from electrostatic discharge:
- 8-50F2 Before testing a RADAR transmitter, it would be a good idea to:
- 8-50F3 While making repairs or adjustments to RADAR units:
- 8-50F4 While removing a CRT from its operating casing, it is a good idea to:
- 8-50F5 If a CRT is dropped:
- 8-50F6 Prior to removing, servicing or making measurements on any solid state circuit boards from the RADAR set, the operator should ensure that: