General Question Pool

All 423 questions, word for word, with the answer and an explanation for each. In use from July 1, 2023 to June 30, 2027.

General exam guide

G1 Commission’s Rules

G1A General class control operator frequency privileges; primary and secondary allocations

  1. G1A01 On which HF and/or MF amateur bands are there portions where General class licensees cannot transmit?
  2. G1A02 On which of the following bands is phone operation prohibited?
  3. G1A03 On which of the following bands is image transmission prohibited?
  4. G1A05 On which of the following frequencies are General class licensees prohibited from operating as control operator?
  5. G1A06 Which of the following applies when the FCC rules designate the amateur service as a secondary user on a band?
  6. G1A07 On which amateur frequencies in the 10-meter band may stations with a General class control operator transmit CW emissions?
  7. G1A08 Which HF bands have segments exclusively allocated to Amateur Extra licensees?
  8. G1A09 Which of the following frequencies is within the General class portion of the 15-meter band?
  9. G1A10 What portion of the 10-meter band is available for repeater use?
  10. G1A11 When General class licensees are not permitted to use the entire voice portion of a band, which portion of the voice segment is available to them?

G1B Antenna structure limitations; good engineering and good amateur practice; beacon operation; prohibited transmissions; retransmitting radio signals

  1. G1B01 What is the maximum height above ground for an antenna structure not near a public use airport without requiring notification to the FAA and registration with the FCC?
  2. G1B02 With which of the following conditions must beacon stations comply?
  3. G1B03 Which of the following is a purpose of a beacon station as identified in the FCC rules?
  4. G1B04 Which of the following transmissions is permitted for all amateur stations?
  5. G1B05 Which of the following one-way transmissions are permitted?
  6. G1B06 Under what conditions are state and local governments permitted to regulate amateur radio antenna structures?
  7. G1B07 What are the restrictions on the use of abbreviations or procedural signals in the amateur service?
  8. G1B08 When is it permissible to communicate with amateur stations in countries outside the areas administered by the Federal Communications Commission?
  9. G1B09 On what HF frequencies are automatically controlled beacons permitted?
  10. G1B10 What is the power limit for beacon stations?
  11. G1B11 Who or what determines “good engineering and good amateur practice,” as applied to the operation of an amateur station in all respects not covered by the Part 97 rules?

G1C Transmitter power regulations; data emission standards; 60-meter operation requirements

  1. G1C01 What is the maximum transmitter power an amateur station may use on 10.140 MHz?
  2. G1C02 What is the maximum transmitter power an amateur station may use on the 12-meter band?
  3. G1C03 What is the maximum bandwidth permitted by FCC rules for amateur radio stations transmitting on USB frequencies in the 60-meter band?
  4. G1C04 Which of the following is required by the FCC rules when operating in the 60-meter band?
  5. G1C05 What is the limit for transmitter power on the 28 MHz band for a General Class control operator?
  6. G1C06 What is the limit for transmitter power on the 1.8 MHz band?
  7. G1C07 What must be done before using a new digital protocol on the air?
  8. G1C11 What measurement is specified by FCC rules that regulate maximum power?

G1D Volunteer Examiners and Volunteer Examiner Coordinators; temporary identification; element credit; remote operation

  1. G1D01 Who may receive partial credit for the elements represented by an expired amateur radio license?
  2. G1D02 What license examinations may you administer as an accredited Volunteer Examiner holding a General class operator license?
  3. G1D03 On which of the following band segments may you operate if you are a Technician class operator and have an unexpired Certificate of Successful Completion of Examination (CSCE) for General class privileges?
  4. G1D04 Who must observe the administration of a Technician class license examination?
  5. G1D05 When operating a US station by remote control from outside the country, what license is required of the control operator?
  6. G1D06 Until an upgrade to General class is shown in the FCC database, when must a Technician licensee identify with “AG” after their call sign?
  7. G1D07 Volunteer Examiners are accredited by what organization?
  8. G1D08 Which of the following criteria must be met for a non-US citizen to be an accredited Volunteer Examiner?
  9. G1D09 How long is a Certificate of Successful Completion of Examination (CSCE) valid for exam element credit?
  10. G1D10 What is the minimum age that one must be to qualify as an accredited Volunteer Examiner?
  11. G1D11 What action is required to obtain a new General class license after a previously held license has expired and the two-year grace period has passed?
  12. G1D12 When operating a station in South America by remote control over the internet from the US, what regulations apply?

G1E Control categories; repeater regulations; third-party rules; ITU regions; automatically controlled digital station

  1. G1E01 Which of the following would disqualify a third party from participating in sending a message via an amateur station?
  2. G1E02 When may a 10-meter repeater retransmit the 2-meter signal from a station that has a Technician class control operator?
  3. G1E03 What is required to conduct communications with a digital station operating under automatic control outside the automatic control band segments?
  4. G1E04 Which of the following conditions require a licensed amateur radio operator to take specific steps to avoid harmful interference to other users or facilities?
  5. G1E05 What are the restrictions on messages sent to a third party in a country with which there is a Third-Party Agreement?
  6. G1E06 The frequency allocations of which ITU region apply to radio amateurs operating in North and South America?
  7. G1E07 In what part of the 2.4 GHz band may an amateur station communicate with non-licensed Wi-Fi stations?
  8. G1E08 What is the maximum PEP output allowed for spread spectrum transmissions?
  9. G1E10 Why should an amateur operator normally avoid transmitting on 14.100, 18.110, 21.150, 24.930 and 28.200 MHz?
  10. G1E11 On what bands may automatically controlled stations transmitting RTTY or data emissions communicate with other automatically controlled digital stations?
  11. G1E12 When may third-party messages be transmitted via remote control?

G2 Operating Procedures

G2A Phone operating procedures: USB/LSB conventions, breaking into a contact, transmitter setup for voice operation; answering DX stations

  1. G2A01 Which mode is most commonly used for voice communications on frequencies of 14 MHz or higher?
  2. G2A02 Which mode is most commonly used for voice communications on the 160-, 75-, and 40-meter bands?
  3. G2A03 Which mode is most commonly used for SSB voice communications in the VHF and UHF bands?
  4. G2A04 Which mode is most commonly used for voice communications on the 17- and 12-meter bands?
  5. G2A05 Which mode of voice communication is most commonly used on the HF amateur bands?
  6. G2A06 Which of the following is an advantage of using single sideband, as compared to other analog voice modes on the HF amateur bands?
  7. G2A07 Which of the following statements is true of single sideband (SSB)?
  8. G2A08 What is the recommended way to break into a phone contact?
  9. G2A09 Why do most amateur stations use lower sideband on the 160-, 75-, and 40-meter bands?
  10. G2A10 Which of the following statements is true of VOX operation versus PTT operation?
  11. G2A11 Generally, who should respond to a station in the contiguous 48 states calling “CQ DX”?
  12. G2A12 What control is typically adjusted for proper ALC setting on a single sideband transceiver?

G2B Operating effectively; band plans; drills and emergencies; RACES operation

  1. G2B01 Which of the following is true concerning access to frequencies?
  2. G2B02 What is the first thing you should do if you are communicating with another amateur station and hear a station in distress break in?
  3. G2B03 What is good amateur practice if propagation changes during a contact creating interference from other stations using the frequency?
  4. G2B04 When selecting a CW transmitting frequency, what minimum separation from other stations should be used to minimize interference to stations on adjacent frequencies?
  5. G2B05 When selecting an SSB transmitting frequency, what minimum separation should be used to minimize interference to stations on adjacent frequencies?
  6. G2B06 How can you avoid harmful interference on an apparently clear frequency before calling CQ on CW or phone?
  7. G2B07 Which of the following complies with commonly accepted amateur practice when choosing a frequency on which to initiate a call?
  8. G2B08 What is the voluntary band plan restriction for US stations transmitting within the 48 contiguous states in the 50.1 MHz to 50.125 MHz band segment?
  9. G2B09 Who may be the control operator of an amateur station transmitting in RACES to assist relief operations during a disaster?
  10. G2B10 Which of the following is good amateur practice for net management?
  11. G2B11 How often may RACES training drills and tests be routinely conducted without special authorization?

G2C CW operating procedures and procedural signals; Q signals; full break-in

  1. G2C01 Which of the following describes full break-in CW operation (QSK)?
  2. G2C02 What should you do if a CW station sends “QRS?”
  3. G2C03 What does it mean when a CW operator sends “KN” at the end of a transmission?
  4. G2C04 What does the Q signal “QRL?” mean?
  5. G2C05 What is the best speed to use when answering a CQ in Morse code?
  6. G2C06 What does the term “zero beat” mean in CW operation?
  7. G2C07 When sending CW, what does a “C” mean when added to the RST report?
  8. G2C08 What prosign is sent to indicate the end of a formal message when using CW?
  9. G2C09 What does the Q signal “QSL” mean?
  10. G2C10 What does the Q signal “QRN” mean?
  11. G2C11 What does the Q signal “QRV” mean?

G2D Volunteer Monitor Program; HF operations

  1. G2D01 What is the Volunteer Monitor Program?
  2. G2D02 Which of the following are objectives of the Volunteer Monitor Program?
  3. G2D03 What procedure may be used by Volunteer Monitors to localize a station whose continuous carrier is holding a repeater on in their area?
  4. G2D04 Which of the following describes an azimuthal projection map?
  5. G2D05 Which of the following indicates that you are looking for an HF contact with any station?
  6. G2D06 How is a directional antenna pointed when making a “long-path” contact with another station?
  7. G2D07 Which of the following are examples of the NATO Phonetic Alphabet?
  8. G2D08 Why do many amateurs keep a station log?
  9. G2D09 Which of the following is required when participating in a contest on HF frequencies?
  10. G2D10 What is QRP operation?
  11. G2D11 Why are signal reports typically exchanged at the beginning of an HF contact?

G2E Digital mode operating procedures

  1. G2E01 Which mode is normally used when sending RTTY signals via AFSK with an SSB transmitter?
  2. G2E02 What is VARA?
  3. G2E03 What symptoms may result from other signals interfering with a PACTOR or VARA transmission?
  4. G2E04 Which of the following is good practice when choosing a transmitting frequency to answer a station calling CQ using FT8?
  5. G2E05 What is the standard sideband for JT65, JT9, FT4, or FT8 digital signal when using AFSK?
  6. G2E06 What is the most common frequency shift for RTTY emissions in the amateur HF bands?
  7. G2E07 Which of the following is required when using FT8?
  8. G2E08 In what segment of the 20-meter band are most digital mode operations commonly found?
  9. G2E09 How do you join a contact between two stations using the PACTOR protocol?
  10. G2E10 Which of the following is a way to establish contact with a digital messaging system gateway station?
  11. G2E11 What is the primary purpose of an Amateur Radio Emergency Data Network (AREDN) mesh network?
  12. G2E12 Which of the following describes Winlink?
  13. G2E13 What is another name for a Winlink Remote Message Server?
  14. G2E14 What could be wrong if you cannot decode an RTTY or other FSK signal even though it is apparently tuned in properly?
  15. G2E15 Which of the following is a common location for FT8?

G3 Radio Wave Propagation

G3A Sunspots and solar radiation; geomagnetic field and stability indices

  1. G3A01 How does a higher sunspot number affect HF propagation?
  2. G3A02 What effect does a sudden ionospheric disturbance have on the daytime ionospheric propagation?
  3. G3A03 Approximately how long does it take the increased ultraviolet and X-ray radiation from a solar flare to affect radio propagation on Earth?
  4. G3A04 Which of the following are the least reliable bands for long-distance communications during periods of low solar activity?
  5. G3A05 What is the solar flux index?
  6. G3A06 What is a geomagnetic storm?
  7. G3A07 At what point in the solar cycle does the 20-meter band usually support worldwide propagation during daylight hours?
  8. G3A08 How can a geomagnetic storm affect HF propagation?
  9. G3A09 How can high geomagnetic activity benefit radio communications?
  10. G3A10 What causes HF propagation conditions to vary periodically in a 26- to 28-day cycle?
  11. G3A11 How long does it take a coronal mass ejection to affect radio propagation on Earth?
  12. G3A12 What does the K-index measure?
  13. G3A13 What does the A-index measure?
  14. G3A14 How is long distance radio communication usually affected by the charged particles that reach Earth from solar coronal holes?

G3B Maximum Usable Frequency; Lowest Usable Frequency; short path and long path propagation; determining propagation conditions; ionospheric refraction

  1. G3B01 What is a characteristic of skywave signals arriving at your location by both short-path and long-path propagation?
  2. G3B02 What factors affect the MUF?
  3. G3B03 Which frequency will have the least attenuation for long-distance skip propagation?
  4. G3B04 Which of the following is a way to determine current propagation on a desired band from your station?
  5. G3B05 How does the ionosphere affect radio waves with frequencies below the MUF and above the LUF?
  6. G3B06 What usually happens to radio waves with frequencies below the LUF?
  7. G3B07 What does LUF stand for?
  8. G3B08 What does MUF stand for?
  9. G3B09 What is the approximate maximum distance along the Earth’s surface normally covered in one hop using the F2 region?
  10. G3B10 What is the approximate maximum distance along the Earth’s surface normally covered in one hop using the E region?
  11. G3B11 What happens to HF propagation when the LUF exceeds the MUF?
  12. G3B12 Which of the following is typical of the lower HF frequencies during the summer?

G3C Ionospheric regions; critical angle and frequency; HF scatter; near vertical incidence skywave (NVIS)

  1. G3C01 Which ionospheric region is closest to the surface of Earth?
  2. G3C02 What is meant by the term “critical frequency” at a given incidence angle?
  3. G3C03 Why is skip propagation via the F2 region longer than that via the other ionospheric regions?
  4. G3C04 What does the term “critical angle” mean, as applied to radio wave propagation?
  5. G3C05 Why is long-distance communication on the 40-, 60-, 80-, and 160-meter bands more difficult during the day?
  6. G3C06 What is a characteristic of HF scatter?
  7. G3C07 What makes HF scatter signals often sound distorted?
  8. G3C08 Why are HF scatter signals in the skip zone usually weak?
  9. G3C09 What type of propagation allows signals to be heard in the transmitting station’s skip zone?
  10. G3C10 What is near vertical incidence skywave (NVIS) propagation?
  11. G3C11 Which ionospheric region is the most absorbent of signals below 10 MHz during daylight hours?

G4 Amateur Radio Practices

G4A Station configuration and operation

  1. G4A01 What is the purpose of the notch filter found on many HF transceivers?
  2. G4A02 What is the benefit of using the opposite or “reverse” sideband when receiving CW?
  3. G4A03 How does a noise blanker work?
  4. G4A04 What is the effect on plate current of the correct setting of a vacuum-tube RF power amplifier’s TUNE control?
  5. G4A05 Why is automatic level control (ALC) used with an RF power amplifier?
  6. G4A06 What is the purpose of an antenna tuner?
  7. G4A07 What happens as a receiver’s noise reduction control level is increased?
  8. G4A08 What is the correct adjustment for the LOAD or COUPLING control of a vacuum tube RF power amplifier?
  9. G4A09 What is the purpose of delaying RF output after activating a transmitter’s keying line to an external amplifier?
  10. G4A10 What is the function of an electronic keyer?
  11. G4A11 Why should the ALC system be inactive when transmitting AFSK data signals?
  12. G4A12 Which of the following is a common use of the dual-VFO feature on a transceiver?
  13. G4A13 What is the purpose of using a receive attenuator?

G4B Tests and test equipment

  1. G4B01 What item of test equipment contains horizontal and vertical channel amplifiers?
  2. G4B02 Which of the following is an advantage of an oscilloscope versus a digital voltmeter?
  3. G4B03 Which of the following is the best instrument to use for checking the keying waveform of a CW transmitter?
  4. G4B04 What signal source is connected to the vertical input of an oscilloscope when checking the RF envelope pattern of a transmitted signal?
  5. G4B05 Why do voltmeters have high input impedance?
  6. G4B06 What is an advantage of a digital multimeter as compared to an analog multimeter?
  7. G4B07 What signals are used to conduct a two-tone test?
  8. G4B08 What transmitter performance parameter does a two-tone test analyze?
  9. G4B09 When is an analog multimeter preferred to a digital multimeter?
  10. G4B10 Which of the following can be determined with a directional wattmeter?
  11. G4B11 Which of the following must be connected to an antenna analyzer when it is being used for SWR measurements?
  12. G4B12 What effect can strong signals from nearby transmitters have on an antenna analyzer?
  13. G4B13 Which of the following can be measured with an antenna analyzer?

G4C Interference to consumer electronics; grounding and bonding

  1. G4C01 Which of the following might be useful in reducing RF interference to audio frequency circuits?
  2. G4C02 Which of the following could be a cause of interference covering a wide range of frequencies?
  3. G4C03 What sound is heard from an audio device experiencing RF interference from a single sideband phone transmitter?
  4. G4C04 What sound is heard from an audio device experiencing RF interference from a CW transmitter?
  5. G4C05 What is a possible cause of high voltages that produce RF burns?
  6. G4C06 What is a possible effect of a resonant ground connection?
  7. G4C07 Why should soldered joints not be used in lightning protection ground connections?
  8. G4C08 Which of the following would reduce RF interference caused by common-mode current on an audio cable?
  9. G4C09 How can the effects of ground loops be minimized?
  10. G4C10 What could be a symptom caused by a ground loop in your station’s audio connections?
  11. G4C11 What technique helps to minimize RF “hot spots” in an amateur station?
  12. G4C12 Why must all metal enclosures of station equipment be grounded?

G4D Speech processors; S meters; sideband operation near band edges

  1. G4D01 What is the purpose of a speech processor in a transceiver?
  2. G4D02 How does a speech processor affect a single sideband phone signal?
  3. G4D03 What is the effect of an incorrectly adjusted speech processor?
  4. G4D04 What does an S meter measure?
  5. G4D05 How does a signal that reads 20 dB over S9 compare to one that reads S9 on a receiver, assuming a properly calibrated S meter?
  6. G4D06 How much change in signal strength is typically represented by one S unit?
  7. G4D07 How much must the power output of a transmitter be raised to change the S meter reading on a distant receiver from S8 to S9?
  8. G4D08 What frequency range is occupied by a 3 kHz LSB signal when the displayed carrier frequency is set to 7.178 MHz?
  9. G4D09 What frequency range is occupied by a 3 kHz USB signal with the displayed carrier frequency set to 14.347 MHz?
  10. G4D10 How close to the lower edge of a band’s phone segment should your displayed carrier frequency be when using 3 kHz wide LSB?
  11. G4D11 How close to the upper edge of a band’s phone segment should your displayed carrier frequency be when using 3 kHz wide USB?

G4E Mobile and portable HF stations; alternative energy source operation

  1. G4E01 What is the purpose of a capacitance hat on a mobile antenna?
  2. G4E02 What is the purpose of a corona ball on an HF mobile antenna?
  3. G4E03 Which of the following direct, fused power connections would be the best for a 100-watt HF mobile installation?
  4. G4E04 Why should DC power for a 100-watt HF transceiver not be supplied by a vehicle’s auxiliary power socket?
  5. G4E05 Which of the following most limits an HF mobile installation?
  6. G4E06 What is one disadvantage of using a shortened mobile antenna as opposed to a full-size antenna?
  7. G4E07 Which of the following may cause receive interference to an HF transceiver installed in a vehicle?
  8. G4E08 In what configuration are the individual cells in a solar panel connected together?
  9. G4E09 What is the approximate open-circuit voltage from a fully illuminated silicon photovoltaic cell?
  10. G4E10 Why should a series diode be connected between a solar panel and a storage battery that is being charged by the panel?
  11. G4E11 What precaution should be taken when connecting a solar panel to a lithium iron phosphate battery?

G5 Electrical Principles

G5A Reactance; inductance; capacitance; impedance; impedance transformation; resonance

  1. G5A01 What happens when inductive and capacitive reactance are equal in a series LC circuit?
  2. G5A02 What is reactance?
  3. G5A03 Which of the following is opposition to the flow of alternating current in an inductor?
  4. G5A04 Which of the following is opposition to the flow of alternating current in a capacitor?
  5. G5A05 How does an inductor react to AC?
  6. G5A06 How does a capacitor react to AC?
  7. G5A07 What is the term for the inverse of impedance?
  8. G5A08 What is impedance?
  9. G5A09 What unit is used to measure reactance?
  10. G5A10 Which of the following devices can be used for impedance matching at radio frequencies?
  11. G5A11 What letter is used to represent reactance?
  12. G5A12 What occurs in an LC circuit at resonance?

G5B The decibel; current and voltage dividers; electrical power calculations; sine wave root-mean-square (RMS) values; PEP calculations

  1. G5B01 What dB change represents a factor of two increase or decrease in power?
  2. G5B02 How does the total current relate to the individual currents in a circuit of parallel resistors?
  3. G5B03 How many watts of electrical power are consumed if 400 VDC is supplied to an 800-ohm load?
  4. G5B04 How many watts of electrical power are consumed by a 12 VDC light bulb that draws 0.2 amperes?
  5. G5B05 How many watts are consumed when a current of 7.0 milliamperes flows through a 1,250-ohm resistance?
  6. G5B06 What is the PEP produced by 200 volts peak-to-peak across a 50-ohm dummy load?
  7. G5B07 What value of an AC signal produces the same power dissipation in a resistor as a DC voltage of the same value?
  8. G5B08 What is the peak-to-peak voltage of a sine wave with an RMS voltage of 120 volts?
  9. G5B09 What is the RMS voltage of a sine wave with a value of 17 volts peak?
  10. G5B10 What percentage of power loss is equivalent to a loss of 1 dB?
  11. G5B11 What is the ratio of PEP to average power for an unmodulated carrier?
  12. G5B12 What is the RMS voltage across a 50-ohm dummy load dissipating 1200 watts?
  13. G5B13 What is the output PEP of an unmodulated carrier if the average power is 1060 watts?
  14. G5B14 What is the output PEP of 500 volts peak-to-peak across a 50-ohm load?

G5C Resistors, capacitors, and inductors in series and parallel; transformers

  1. G5C01 What causes a voltage to appear across the secondary winding of a transformer when an AC voltage source is connected across its primary winding?
  2. G5C02 What is the output voltage if an input signal is applied to the secondary winding of a 4:1 voltage step-down transformer instead of the primary winding?
  3. G5C03 What is the total resistance of a 10-, a 20-, and a 50-ohm resistor connected in parallel?
  4. G5C04 What is the approximate total resistance of a 100- and a 200-ohm resistor in parallel?
  5. G5C05 Why is the primary winding wire of a voltage step-up transformer usually a larger size than that of the secondary winding?
  6. G5C06 What is the voltage output of a transformer with a 500-turn primary and a 1500-turn secondary when 120 VAC is applied to the primary?
  7. G5C07 What transformer turns ratio matches an antenna’s 600-ohm feed point impedance to a 50-ohm coaxial cable?
  8. G5C08 What is the equivalent capacitance of two 5.0-nanofarad capacitors and one 750-picofarad capacitor connected in parallel?
  9. G5C09 What is the capacitance of three 100-microfarad capacitors connected in series?
  10. G5C10 What is the inductance of three 10-millihenry inductors connected in parallel?
  11. G5C11 What is the inductance of a circuit with a 20-millihenry inductor connected in series with a 50-millihenry inductor?
  12. G5C12 What is the capacitance of a 20-microfarad capacitor connected in series with a 50-microfarad capacitor?
  13. G5C13 Which of the following components should be added to a capacitor to increase the capacitance?
  14. G5C14 Which of the following components should be added to an inductor to increase the inductance?

G6 Circuit Components

G6A Resistors; capacitors; inductors; rectifiers; solid-state diodes and transistors; vacuum tubes; batteries

  1. G6A01 What is the minimum allowable discharge voltage for maximum life of a standard 12-volt lead-acid battery?
  2. G6A02 What is an advantage of batteries with low internal resistance?
  3. G6A03 What is the approximate forward threshold voltage of a germanium diode?
  4. G6A04 Which of the following is characteristic of an electrolytic capacitor?
  5. G6A05 What is the approximate forward threshold voltage of a silicon junction diode?
  6. G6A06 Why should wire-wound resistors not be used in RF circuits?
  7. G6A07 What are the operating points for a bipolar transistor used as a switch?
  8. G6A08 Which of the following is characteristic of low voltage ceramic capacitors?
  9. G6A09 Which of the following describes MOSFET construction?
  10. G6A10 Which element of a vacuum tube regulates the flow of electrons between cathode and plate?
  11. G6A11 What happens when an inductor is operated above its self-resonant frequency?
  12. G6A12 What is the primary purpose of a screen grid in a vacuum tube?

G6B Analog and digital integrated circuits (ICs); microwave ICs (MMICs); display devices; RF connectors; ferrite cores

  1. G6B01 What determines the performance of a ferrite core at different frequencies?
  2. G6B02 What is meant by the term MMIC?
  3. G6B03 Which of the following is an advantage of CMOS integrated circuits compared to TTL integrated circuits?
  4. G6B04 What is a typical upper frequency limit for low SWR operation of 50-ohm BNC connectors?
  5. G6B05 What is an advantage of using a ferrite core toroidal inductor?
  6. G6B06 What kind of device is an integrated circuit operational amplifier?
  7. G6B07 Which of the following describes a type N connector?
  8. G6B08 How is an LED biased when emitting light?
  9. G6B10 How does a ferrite bead or core reduce common-mode RF current on the shield of a coaxial cable?
  10. G6B11 What is an SMA connector?
  11. G6B12 Which of these connector types is commonly used for low frequency or dc signal connections to a transceiver?

G7 Practical Circuits

G7A Power supplies; schematic symbols

  1. G7A01 What is the function of a power supply bleeder resistor?
  2. G7A02 Which of the following components are used in a power supply filter network?
  3. G7A03 Which type of rectifier circuit uses two diodes and a center-tapped transformer?
  4. G7A04 What is characteristic of a half-wave rectifier in a power supply?
  5. G7A05 What portion of the AC cycle is converted to DC by a half-wave rectifier?
  6. G7A06 What portion of the AC cycle is converted to DC by a full-wave rectifier?
  7. G7A07 What is the output waveform of an unfiltered full-wave rectifier connected to a resistive load?
  8. G7A08 Which of the following is characteristic of a switchmode power supply as compared to a linear power supply?
  9. G7A09 Which symbol in figure G7-1 represents a field effect transistor?
  10. G7A10 Which symbol in figure G7-1 represents a Zener diode?
  11. G7A11 Which symbol in figure G7-1 represents an NPN junction transistor?
  12. G7A12 Which symbol in Figure G7-1 represents a solid core transformer?
  13. G7A13 Which symbol in Figure G7-1 represents a tapped inductor?

G7B Digital circuits; amplifiers and oscillators

  1. G7B01 What is the purpose of neutralizing an amplifier?
  2. G7B02 Which of these classes of amplifiers has the highest efficiency?
  3. G7B03 Which of the following describes the function of a two-input AND gate?
  4. G7B04 In a Class A amplifier, what percentage of the time does the amplifying device conduct?
  5. G7B05 How many states does a 3-bit binary counter have?
  6. G7B06 What is a shift register?
  7. G7B07 Which of the following are basic components of a sine wave oscillator?
  8. G7B08 How is the efficiency of an RF power amplifier determined?
  9. G7B09 What determines the frequency of an LC oscillator?
  10. G7B10 Which of the following describes a linear amplifier?
  11. G7B11 For which of the following modes is a Class C power stage appropriate for amplifying a modulated signal?

G7C Transceiver design; filters; oscillators; digital signal processing (DSP)

  1. G7C01 What circuit is used to select one of the sidebands from a balanced modulator?
  2. G7C02 What output is produced by a balanced modulator?
  3. G7C03 What is one reason to use an impedance matching transformer at a transmitter output?
  4. G7C04 How is a product detector used?
  5. G7C05 Which of the following is characteristic of a direct digital synthesizer (DDS)?
  6. G7C06 Which of the following is an advantage of a digital signal processing (DSP) filter compared to an analog filter?
  7. G7C07 What term specifies a filter’s attenuation inside its passband?
  8. G7C08 Which parameter affects receiver sensitivity?
  9. G7C09 What is the phase difference between the I and Q RF signals that software-defined radio (SDR) equipment uses for modulation and demodulation?
  10. G7C10 What is an advantage of using I-Q modulation with software-defined radios (SDRs)?
  11. G7C11 Which of these functions is performed by software in a software-defined radio (SDR)?
  12. G7C12 What is the frequency above which a low-pass filter’s output power is less than half the input power?
  13. G7C13 What term specifies a filter’s maximum ability to reject signals outside its passband?
  14. G7C14 The bandwidth of a band-pass filter is measured between what two frequencies?

G8 Signals and Emissions

G8A Carriers and modulation: AM, FM, and single sideband; modulation envelope; digital modulation; overmodulation; link budgets and link margins

  1. G8A01 How is direct binary FSK modulation generated?
  2. G8A02 What is the name of the process that changes the phase angle of an RF signal to convey information?
  3. G8A03 What is the name of the process that changes the instantaneous frequency of an RF wave to convey information?
  4. G8A04 What emission is produced by a reactance modulator connected to a transmitter RF amplifier stage?
  5. G8A05 What type of modulation varies the instantaneous power level of the RF signal?
  6. G8A06 Which of the following is characteristic of QPSK31?
  7. G8A07 Which of the following phone emissions uses the narrowest bandwidth?
  8. G8A08 Which of the following is an effect of overmodulation?
  9. G8A09 What type of modulation is used by FT8?
  10. G8A10 What is meant by the term “flat-topping,” when referring to an amplitude-modulated phone signal?
  11. G8A11 What is the modulation envelope of an AM signal?
  12. G8A12 What is QPSK modulation?
  13. G8A13 What is a link budget?
  14. G8A14 What is link margin?

G8B Frequency changing; bandwidths of various modes; deviation; intermodulation

  1. G8B01 Which mixer input is varied or tuned to convert signals of different frequencies to an intermediate frequency (IF)?
  2. G8B02 What is the term for interference from a signal at twice the IF frequency from the desired signal?
  3. G8B03 What is another term for the mixing of two RF signals?
  4. G8B04 What is the stage in a VHF FM transmitter that generates a harmonic of a lower frequency signal to reach the desired operating frequency?
  5. G8B05 Which intermodulation products are closest to the original signal frequencies?
  6. G8B06 What is the total bandwidth of an FM phone transmission having 5 kHz deviation and 3 kHz modulating frequency?
  7. G8B07 What is the frequency deviation for a 12.21 MHz reactance modulated oscillator in a 5 kHz deviation, 146.52 MHz FM phone transmitter?
  8. G8B08 Why is it important to know the duty cycle of the mode you are using when transmitting?
  9. G8B09 Why is it good to match receiver bandwidth to the bandwidth of the operating mode?
  10. G8B10 What is the relationship between transmitted symbol rate and bandwidth?
  11. G8B11 What combination of a mixer’s Local Oscillator (LO) and RF input frequencies is found in the output?
  12. G8B12 What process combines two signals in a non-linear circuit to produce unwanted spurious outputs?
  13. G8B13 Which of the following is an odd-order intermodulation product of frequencies F1 and F2?

G8C Digital emission modes

  1. G8C02 Which digital mode is used as a low-power beacon for assessing HF propagation?
  2. G8C03 What part of a packet radio frame contains the routing and handling information?
  3. G8C04 Which of the following describes Baudot code?
  4. G8C05 In an ARQ mode, what is meant by a NAK response to a transmitted packet?
  5. G8C06 What action results from a failure to exchange information due to excessive transmission attempts when using an ARQ mode?
  6. G8C07 Which of the following narrow-band digital modes can receive signals with very low signal-to-noise ratios?
  7. G8C08 Which of the following statements is true about PSK31?
  8. G8C09 Which is true of mesh network microwave nodes?
  9. G8C10 How does forward error correction (FEC) allow the receiver to correct data errors?
  10. G8C11 How are the two separate frequencies of a Frequency Shift Keyed (FSK) signal identified?
  11. G8C12 Which type of code is used for sending characters in a PSK31 signal?
  12. G8C13 What is indicated on a waterfall display by one or more vertical lines on either side of a data mode or RTTY signal?
  13. G8C14 Which of the following describes a waterfall display?
  14. G8C15 What does an FT8 signal report of +3 mean?
  15. G8C16 Which of the following provide digital voice modes?

G9 Antennas and Feed Lines

G9A Feed lines: characteristic impedance and attenuation; standing wave ratio (SWR) calculation, measurement, and effects; antenna feed point matching

  1. G9A01 Which of the following factors determine the characteristic impedance of a parallel conductor feed line?
  2. G9A02 What is the relationship between high standing wave ratio (SWR) and transmission line loss?
  3. G9A03 What is the nominal characteristic impedance of “window line” transmission line?
  4. G9A04 What causes reflected power at an antenna’s feed point?
  5. G9A05 How does the attenuation of coaxial cable change with increasing frequency?
  6. G9A06 In what units is RF feed line loss usually expressed?
  7. G9A07 What must be done to prevent standing waves on a feed line connected to an antenna?
  8. G9A08 If the SWR on an antenna feed line is 5:1, and a matching network at the transmitter end of the feed line is adjusted to present a 1:1 SWR to the transmitter, what is the resulting SWR on the feed line?
  9. G9A09 What standing wave ratio results from connecting a 50-ohm feed line to a 200-ohm resistive load?
  10. G9A10 What standing wave ratio results from connecting a 50-ohm feed line to a 10-ohm resistive load?
  11. G9A11 What is the effect of transmission line loss on SWR measured at the input to the line?

G9B Basic dipole and monopole antennas

  1. G9B01 What is a characteristic of a random-wire HF antenna connected directly to the transmitter?
  2. G9B02 Which of the following is a common way to adjust the feed point impedance of an elevated quarter-wave ground-plane vertical antenna to be approximately 50 ohms?
  3. G9B03 Which of the following best describes the radiation pattern of a quarter-wave ground-plane vertical antenna?
  4. G9B04 What is the radiation pattern of a dipole antenna in free space in a plane containing the conductor?
  5. G9B05 How does antenna height affect the azimuthal radiation pattern of a horizontal dipole HF antenna at elevation angles higher than about 45 degrees?
  6. G9B06 Where should the radial wires of a ground-mounted vertical antenna system be placed?
  7. G9B07 How does the feed point impedance of a horizontal 1/2 wave dipole antenna change as the antenna height is reduced to 1/10 wavelength above ground?
  8. G9B08 How does the feed point impedance of a 1/2 wave dipole change as the feed point is moved from the center toward the ends?
  9. G9B09 Which of the following is an advantage of using a horizontally polarized as compared to a vertically polarized HF antenna?
  10. G9B10 What is the approximate length for a 1/2 wave dipole antenna cut for 14.250 MHz?
  11. G9B11 What is the approximate length for a 1/2 wave dipole antenna cut for 3.550 MHz?
  12. G9B12 What is the approximate length for a 1/4 wave monopole antenna cut for 28.5 MHz?

G9C Directional antennas

  1. G9C01 Which of the following would increase the bandwidth of a Yagi antenna?
  2. G9C02 What is the approximate length of the driven element of a Yagi antenna?
  3. G9C03 How do the lengths of a three-element Yagi reflector and director compare to that of the driven element?
  4. G9C04 How does antenna gain in dBi compare to gain stated in dBd for the same antenna?
  5. G9C05 What is the primary effect of increasing boom length and adding directors to a Yagi antenna?
  6. G9C07 What does “front-to-back ratio” mean in reference to a Yagi antenna?
  7. G9C08 What is meant by the “main lobe” of a directive antenna?
  8. G9C09 In free space, how does the gain of two three-element, horizontally polarized Yagi antennas spaced vertically 1/2 wavelength apart typically compare to the gain of a single three-element Yagi?
  9. G9C10 Which of the following can be adjusted to optimize forward gain, front-to-back ratio, or SWR bandwidth of a Yagi antenna?
  10. G9C11 What is a beta or hairpin match?
  11. G9C12 Which of the following is a characteristic of using a gamma match with a Yagi antenna?

G9D Specialized antenna types and applications

  1. G9D01 Which of the following antenna types will be most effective as a near vertical incidence skywave (NVIS) antenna for short-skip communications on 40 meters during the day?
  2. G9D02 What is the feed point impedance of an end-fed half-wave antenna?
  3. G9D03 In which direction is the maximum radiation from a VHF/UHF “halo” antenna?
  4. G9D04 What is the primary function of antenna traps?
  5. G9D05 What is an advantage of vertically stacking horizontally polarized Yagi antennas?
  6. G9D06 Which of the following is an advantage of a log-periodic antenna?
  7. G9D07 Which of the following describes a log-periodic antenna?
  8. G9D08 How does a “screwdriver” mobile antenna adjust its feed point impedance?
  9. G9D09 What is the primary use of a Beverage antenna?
  10. G9D10 In which direction or directions does an electrically small loop (less than 1/10 wavelength in circumference) have nulls in its radiation pattern?
  11. G9D11 Which of the following is a disadvantage of multiband antennas?
  12. G9D12 What is the common name of a dipole with a single central support?

G0 Electrical and RF Safety

G0A RF safety principles, rules, and guidelines; routine station evaluation

  1. G0A01 What is one way that RF energy can affect human body tissue?
  2. G0A02 Which of the following is used to determine RF exposure from a transmitted signal?
  3. G0A03 How can you determine that your station complies with FCC RF exposure regulations?
  4. G0A04 What does “time averaging” mean when evaluating RF radiation exposure?
  5. G0A05 What must you do if an evaluation of your station shows that the RF energy radiated by your station exceeds permissible limits for possible human absorption?
  6. G0A06 What must you do if your station fails to meet the FCC RF exposure exemption criteria?
  7. G0A07 What is the effect of modulation duty cycle on RF exposure?
  8. G0A08 Which of the following steps must an amateur operator take to ensure compliance with RF safety regulations?
  9. G0A09 What type of instrument can be used to accurately measure an RF field strength?
  10. G0A10 What should be done if evaluation shows that a neighbor might experience more than the allowable limit of RF exposure from the main lobe of a directional antenna?
  11. G0A11 What precaution should be taken if you install an indoor transmitting antenna?
  12. G0A12 What stations are subject to the FCC rules on RF exposure?

G0B Station safety: electrical shock, grounding, fusing, interlocks, and wiring; antenna and tower safety

  1. G0B01 Which wire or wires in a four-conductor 240 VAC circuit should be attached to fuses or circuit breakers?
  2. G0B02 According to the National Electrical Code, what is the minimum wire size that may be used safely for wiring with a 20-ampere circuit breaker?
  3. G0B03 Which size of fuse or circuit breaker would be appropriate to use with a circuit that uses AWG number 14 wiring?
  4. G0B04 Where should the station’s lightning protection ground system be located?
  5. G0B05 Which of the following conditions will cause a ground fault circuit interrupter (GFCI) to disconnect AC power?
  6. G0B06 Which of the following is covered by the National Electrical Code?
  7. G0B07 Which of these choices should be observed when climbing a tower using a safety harness?
  8. G0B08 What should be done before climbing a tower that supports electrically powered devices?
  9. G0B09 Which of the following is true of an emergency generator installation?
  10. G0B10 Which of the following is a danger from lead-tin solder?
  11. G0B11 Which of the following is required for lightning protection ground rods?
  12. G0B12 What is the purpose of a power supply interlock?
  13. G0B13 Where should lightning arrestors be located?