Amateur Extra Question Pool
All 599 questions, word for word, with the answer and an explanation for each. In use from July 1, 2024 to June 30, 2028.
E1 Commission Rules
E1A Frequency privileges; signal frequency range; automatic message forwarding; stations aboard ships or aircraft; power restriction on 630- and 2200-meter bands
- E1A01 Why is it not legal to transmit a 3 kHz bandwidth USB signal with a carrier frequency of 14.348 MHz?
- E1A02 When using a transceiver that displays the carrier frequency of phone signals, which of the following displayed frequencies represents the lowest frequency at which a properly adjusted LSB emission will be totally within the band?
- E1A03 What is the highest legal carrier frequency on the 20-meter band for transmitting a 2.8 kHz wide USB data signal?
- E1A04 May an Extra class operator answer the CQ of a station on 3.601 MHz LSB phone?
- E1A05 Who must be in physical control of the station apparatus of an amateur station aboard any vessel or craft that is documented or registered in the United States?
- E1A06 What is the required transmit frequency of a CW signal for channelized 60 meter operation?
- E1A07 What is the maximum power permitted on the 2200-meter band?
- E1A08 If a station in a message forwarding system inadvertently forwards a message that is in violation of FCC rules, who is primarily accountable for the rules violation?
- E1A09 Except in some parts of Alaska, what is the maximum power permitted on the 630-meter band?
- E1A10 If an amateur station is installed aboard a ship or aircraft, what condition must be met before the station is operated?
- E1A11 What licensing is required when operating an amateur station aboard a US-registered vessel in international waters?
E1B Station restrictions and special operations: restrictions on station location; general operating restrictions; spurious emissions; antenna structure restrictions; RACES operations
- E1B01 Which of the following constitutes a spurious emission?
- E1B02 Which of the following is an acceptable bandwidth for digital voice or slow-scan TV transmissions made on the HF amateur bands?
- E1B03 Within what distance must an amateur station protect an FCC monitoring facility from harmful interference?
- E1B04 What must the control operator of a repeater operating in the 70-centimeter band do if a radiolocation system experiences interference from that repeater?
- E1B05 What is the National Radio Quiet Zone?
- E1B06 Which of the following additional rules apply if you are erecting an amateur station antenna structure at a site at or near a public use airport?
- E1B07 To what type of regulations does PRB-1 apply?
- E1B08 What limitations may the FCC place on an amateur station if its signal causes interference to domestic broadcast reception, assuming that the receivers involved are of good engineering design?
- E1B09 Which amateur stations may be operated under RACES rules?
- E1B10 What frequencies are authorized to an amateur station operating under RACES rules?
- E1B11 What does PRB-1 require of state and local regulations affecting amateur radio antenna size and structures?
E1C Automatic and remote control; band-specific regulations; operating in and communicating with foreign countries; spurious emission standards; HF modulation index limit; band-specific rules
- E1C01 What is the maximum bandwidth for a data emission on 60 meters?
- E1C02 Which of the following apply to communications transmitted to amateur stations in foreign countries?
- E1C03 How long must an operator wait after filing a notification with the Utilities Technology Council (UTC) before operating on the 2200-meter or 630-meter band?
- E1C04 What is an IARP?
- E1C05 Under what situation may a station transmit third party communications while being automatically controlled?
- E1C06 Which of the following is required in order to operate in accordance with CEPT rules in foreign countries where permitted?
- E1C07 What notifications must be given before transmitting on the 630- or 2200-meter bands?
- E1C08 What is the maximum permissible duration of a remotely controlled station’s transmissions if its control link malfunctions?
- E1C09 What is the highest modulation index permitted at the highest modulation frequency for angle modulation below 29.0 MHz?
- E1C10 What is the maximum mean power level for a spurious emission below 30 MHz with respect to the fundamental emission?
- E1C11 Which of the following operating arrangements allows an FCC-licensed US citizen to operate in many European countries, and amateurs from many European countries to operate in the US?
- E1C12 In what portion of the 630-meter band are phone emissions permitted?
E1D Amateur Space and Earth stations; telemetry and telecommand rules; identification of balloon transmissions; one-way communications
- E1D01 What is the definition of telemetry?
- E1D02 Which of the following may transmit encrypted messages?
- E1D03 What is a space telecommand station?
- E1D04 Which of the following is required in the identification transmissions from a balloon-borne telemetry station?
- E1D05 What must be posted at the location of a station being operated by telecommand on or within 50 kilometers of the Earth’s surface?
- E1D06 What is the maximum permitted transmitter output power when operating a model craft by telecommand?
- E1D07 Which of the following HF amateur bands include allocations for space stations?
- E1D08 Which VHF amateur bands have frequencies authorized for space stations?
- E1D09 Which UHF amateur bands have frequencies authorized for space stations?
- E1D10 Which amateur stations are eligible to be telecommand stations of space stations, subject to the privileges of the class of operator license held by the control operator of the station?
- E1D11 Which amateur stations are eligible to operate as Earth stations?
- E1D12 Which of the following amateur stations may transmit one-way communications?
E1E Volunteer examiner program: definitions; qualifications; preparation and administration of exams; reimbursement; accreditation; question pools; documentation requirements
- E1E01 For which types of out-of-pocket expenses do the Part 97 rules state that VEs and VECs may be reimbursed?
- E1E02 Who is tasked by Part 97 with maintaining the pools of questions for all US amateur license examinations?
- E1E03 What is a Volunteer Examiner Coordinator?
- E1E04 What is required to be accredited as a Volunteer Examiner?
- E1E05 What must the VE team do with the application form if the examinee does not pass the exam?
- E1E06 Who is responsible for the proper conduct and necessary supervision during an amateur operator license examination session?
- E1E07 What should a VE do if a candidate fails to comply with the examiner’s instructions during an amateur operator license examination?
- E1E08 To which of the following examinees may a VE not administer an examination?
- E1E09 What may be the penalty for a VE who fraudulently administers or certifies an examination?
- E1E10 What must the administering VEs do after the administration of a successful examination for an amateur operator license?
- E1E11 What must the VE team do if an examinee scores a passing grade on all examination elements needed for an upgrade or new license?
E1F Miscellaneous rules: external RF power amplifiers; prohibited communications; spread spectrum; auxiliary stations; Canadian amateurs operating in the US; special temporary authority
- E1F01 On what frequencies are spread spectrum transmissions permitted?
- E1F02 What privileges are authorized in the US to persons holding an amateur service license granted by the government of Canada?
- E1F03 Under what circumstances may a dealer sell an external RF power amplifier capable of operation below 144 MHz if it has not been granted FCC certification?
- E1F04 Which of the following geographic descriptions approximately describes "Line A"?
- E1F05 Amateur stations may not transmit in which of the following frequency segments if they are located in the contiguous 48 states and north of Line A?
- E1F06 Under what circumstances might the FCC issue a Special Temporary Authority (STA) to an amateur station?
- E1F07 When may an amateur station send a message to a business?
- E1F08 Which of the following types of amateur station communications are prohibited?
- E1F09 Which of the following cannot be transmitted over an amateur radio mesh network?
- E1F10 Who may be the control operator of an auxiliary station?
- E1F11 Which of the following best describes one of the standards that must be met by an external RF power amplifier if it is to qualify for a grant of FCC certification?
E2 Operating Procedures
E2A Amateur radio in space: amateur satellites; orbital mechanics; frequencies and modes; satellite hardware; satellite operations
- E2A01 What is the direction of an ascending pass for an amateur satellite?
- E2A02 Which of the following is characteristic of an inverting linear transponder?
- E2A03 How is an upload signal processed by an inverting linear transponder?
- E2A04 What is meant by the “mode” of an amateur radio satellite?
- E2A05 What do the letters in a satellite’s mode designator specify?
- E2A06 What are Keplerian elements?
- E2A07 Which of the following types of signals can be relayed through a linear transponder?
- E2A08 Why should effective radiated power (ERP) be limited to a satellite that uses a linear transponder?
- E2A09 What do the terms “L band” and “S band” specify?
- E2A10 What type of satellite appears to stay in one position in the sky?
- E2A11 What type of antenna can be used to minimize the effects of spin modulation and Faraday rotation?
- E2A12 What is the purpose of digital store-and-forward functions on an amateur radio satellite?
E2B Television practices: fast-scan television standards and techniques; slow scan television standards and techniques
- E2B01 In digital television, what does a coding rate of 3/4 mean?
- E2B02 How many horizontal lines make up a fast-scan (NTSC) television frame?
- E2B03 How is an interlaced scanning pattern generated in a fast-scan (NTSC) television system?
- E2B04 How is color information sent in analog SSTV?
- E2B05 Which of the following describes the use of vestigial sideband in analog fast-scan TV transmissions?
- E2B06 What is vestigial sideband modulation?
- E2B07 Which types of modulation are used for amateur television DVB-T signals?
- E2B08 What technique allows commercial analog TV receivers to be used for fast-scan TV operations on the 70-centimeter band?
- E2B09 What kind of receiver can be used to receive and decode SSTV using the Digital Radio Mondiale (DRM) protocol?
- E2B10 What aspect of an analog slow-scan television signal encodes the brightness of the picture?
- E2B11 What is the function of the vertical interval signaling (VIS) code sent as part of an SSTV transmission?
- E2B12 What signals SSTV receiving software to begin a new picture line?
E2C Contest and DX operating; remote operation techniques; log data format; contact confirmation; RF network systems
- E2C01 What indicator is required to be used by US-licensed operators when operating a station via remote control and the remote transmitter is located in the US?
- E2C02 Which of the following file formats is used for exchanging amateur radio log data?
- E2C03 From which of the following bands is amateur radio contesting generally excluded?
- E2C04 Which of the following frequencies can be used for amateur radio mesh networks?
- E2C05 What is the function of a DX QSL Manager?
- E2C06 During a VHF/UHF contest, in which band segment would you expect to find the highest level of SSB or CW activity?
- E2C07 What is the Cabrillo format?
- E2C08 Which of the following contacts may be confirmed through the Logbook of The World (LoTW)?
- E2C09 What type of equipment is commonly used to implement an amateur radio mesh network?
- E2C10 Why do DX stations often transmit and receive on different frequencies?
- E2C11 How should you generally identify your station when attempting to contact a DX station during a contest or in a pileup?
- E2C12 What indicates the delay between a control operator action and the corresponding change in the transmitted signal?
E2D Operating methods: digital modes and procedures for VHF and UHF; APRS; EME procedures; meteor scatter procedures
- E2D01 Which of the following digital modes is designed for meteor scatter communications?
- E2D02 What information replaces signal-to-noise ratio when using the FT8 or FT4 modes in a VHF contest?
- E2D03 Which of the following digital modes is designed for EME communications?
- E2D04 What technology is used for real-time tracking of balloons carrying amateur radio transmitters?
- E2D05 What is the characteristic of the JT65 mode?
- E2D06 Which of the following is a method for establishing EME contacts?
- E2D07 What digital protocol is used by APRS?
- E2D08 What type of packet frame is used to transmit APRS beacon data?
- E2D09 What type of modulation is used by JT65?
- E2D10 What does the packet path WIDE3-1 designate?
- E2D11 How do APRS stations relay data?
E2E Operating methods: digital modes and procedures for HF
- E2E01 Which of the following types of modulation is used for data emissions below 30 MHz?
- E2E02 Which of the following synchronizes WSJT-X digital mode transmit/receive timing?
- E2E03 To what does the "4" in FT4 refer?
- E2E04 Which of the following is characteristic of the FST4 mode?
- E2E05 Which of these digital modes does not support keyboard-to-keyboard operation?
- E2E06 What is the length of an FT8 transmission cycle?
- E2E07 How does Q65 differ from JT65?
- E2E08 Which of the following HF digital modes can be used to transfer binary files?
- E2E09 Which of the following HF digital modes uses variable-length character coding?
- E2E10 Which of these digital modes has the narrowest bandwidth?
- E2E11 What is the difference between direct FSK and audio FSK?
- E2E12 How do ALE stations establish contact?
- E2E13 Which of these digital modes has the highest data throughput under clear communication conditions?
E3 Radio Wave Propagation
E3A Electromagnetic Waves and Specialized Propagation: Earth-Moon-Earth (EME) communications; meteor scatter; microwave tropospheric and scatter propagation; auroral propagation; daily variation of ionospheric propagation; circular polarization
- E3A01 What is the approximate maximum separation measured along the surface of the Earth between two stations communicating by EME?
- E3A02 What characterizes libration fading of an EME signal?
- E3A03 When scheduling EME contacts, which of these conditions will generally result in the least path loss?
- E3A04 In what direction does an electromagnetic wave travel?
- E3A05 How are the component fields of an electromagnetic wave oriented?
- E3A06 What should be done to continue a long-distance contact when the MUF for that path decreases due to darkness?
- E3A07 Atmospheric ducts capable of propagating microwave signals often form over what geographic feature?
- E3A08 When a meteor strikes the Earth’s atmosphere, a linear ionized region is formed at what region of the ionosphere?
- E3A09 Which of the following frequency ranges is most suited for meteor-scatter communications?
- E3A10 What determines the speed of electromagnetic waves through a medium?
- E3A11 What is a typical range for tropospheric duct propagation of microwave signals?
- E3A12 What is most likely to result in auroral propagation?
- E3A13 Which of these emission modes is best for auroral propagation?
- E3A14 What are circularly polarized electromagnetic waves?
E3B Transequatorial propagation; long-path propagation; ordinary and extraordinary waves; chordal hop; sporadic-E mechanisms; ground-wave propagation
- E3B01 Where is transequatorial propagation (TEP) most likely to occur?
- E3B02 What is the approximate maximum range for signals using transequatorial propagation?
- E3B03 At what time of day is transequatorial propagation most likely to occur?
- E3B04 What are “extraordinary” and “ordinary” waves?
- E3B05 Which of the following paths is most likely to support long-distance propagation on 160 meters?
- E3B06 On which of the following amateur bands is long-path propagation most frequent?
- E3B07 What effect does lowering a signal’s transmitted elevation angle have on ionospheric HF skip propagation?
- E3B08 How does the maximum range of ground-wave propagation change when the signal frequency is increased?
- E3B09 At what time of year is sporadic-E propagation most likely to occur?
- E3B10 What is the effect of chordal-hop propagation?
- E3B11 At what time of day is sporadic-E propagation most likely to occur?
- E3B12 What is chordal-hop propagation?
- E3B13 What type of polarization is supported by ground-wave propagation?
E3C Propagation prediction and reporting: radio horizon; effects of space-weather phenomena
- E3C01 What is the cause of short-term radio blackouts?
- E3C02 What is indicated by a rising A-index or K-index?
- E3C03 Which of the following signal paths is most likely to experience high levels of absorption when the A-index or K-index is elevated?
- E3C04 What does the value of Bz (B sub z) represent?
- E3C05 What orientation of Bz (B sub z) increases the likelihood that charged particles from the Sun will cause disturbed conditions?
- E3C06 How does the VHF/UHF radio horizon compare to the geographic horizon?
- E3C07 Which of the following indicates the greatest solar flare intensity?
- E3C08 Which of the following is the space-weather term for an extreme geomagnetic storm?
- E3C09 What type of data is reported by amateur radio propagation reporting networks?
- E3C10 What does the 304A solar parameter measure?
- E3C11 What does VOACAP software model?
- E3C12 Which of the following is indicated by a sudden rise in radio background noise across a large portion of the HF spectrum?
E4 Amateur Practices
E4A Test equipment: analog and digital instruments; spectrum analyzers; antenna analyzers; oscilloscopes; RF measurements
- E4A01 Which of the following limits the highest frequency signal that can be accurately displayed on a digital oscilloscope?
- E4A02 Which of the following parameters does a spectrum analyzer display on the vertical and horizontal axes?
- E4A03 Which of the following test instruments is used to display spurious signals and/or intermodulation distortion products generated by an SSB transmitter?
- E4A04 How is compensation of an oscilloscope probe performed?
- E4A05 What is the purpose of using a prescaler with a frequency counter?
- E4A06 What is the effect of aliasing on a digital oscilloscope when displaying a waveform?
- E4A07 Which of the following is an advantage of using an antenna analyzer compared to an SWR bridge?
- E4A08 Which of the following is used to measure SWR?
- E4A09 Which of the following is good practice when using an oscilloscope probe?
- E4A10 Which trigger mode is most effective when using an oscilloscope to measure a linear power supply’s output ripple?
- E4A11 Which of the following can be measured with an antenna analyzer?
E4B Measurement technique and limitations: instrument accuracy and performance limitations; probes; techniques to minimize errors; measurement of Q; instrument calibration; S parameters; vector network analyzers; RF signals
- E4B01 Which of the following factors most affects the accuracy of a frequency counter?
- E4B02 What is the significance of voltmeter sensitivity expressed in ohms per volt?
- E4B03 Which S parameter is equivalent to forward gain?
- E4B04 Which S parameter represents input port return loss or reflection coefficient (equivalent to VSWR)?
- E4B05 What three test loads are used to calibrate an RF vector network analyzer?
- E4B06 How much power is being absorbed by the load when a directional power meter connected between a transmitter and a terminating load reads 100 watts forward power and 25 watts reflected power?
- E4B07 What do the subscripts of S parameters represent?
- E4B08 Which of the following can be used to determine the Q of a series-tuned circuit?
- E4B09 Which of the following can be measured by a two-port vector network analyzer?
- E4B10 Which of the following methods measures intermodulation distortion in an SSB transmitter?
- E4B11 Which of the following can be measured with a vector network analyzer?
E4C Receiver performance: phase noise, noise floor, image rejection, minimum detectable signal (MDS), increasing signal-to-noise ratio and dynamic range, noise figure, reciprocal mixing; selectivity; SDR non-linearity; use of attenuators at low frequencies
- E4C01 What is an effect of excessive phase noise in an SDR receiver’s master clock oscillator?
- E4C02 Which of the following receiver circuits can be effective in eliminating interference from strong out-of-band signals?
- E4C03 What is the term for the suppression in an FM receiver of one signal by another stronger signal on the same frequency?
- E4C04 What is the noise figure of a receiver?
- E4C05 What does a receiver noise floor of -174 dBm represent?
- E4C06 How much does increasing a receiver’s bandwidth from 50 Hz to 1,000 Hz increase the receiver’s noise floor?
- E4C07 What does the MDS of a receiver represent?
- E4C08 An SDR receiver is overloaded when input signals exceed what level?
- E4C09 Which of the following choices is a good reason for selecting a high IF for a superheterodyne HF or VHF communications receiver?
- E4C10 What is an advantage of having a variety of receiver bandwidths from which to select?
- E4C11 Why does input attenuation reduce receiver overload on the lower frequency HF bands with little or no impact on signal-to-noise ratio?
- E4C12 How does a narrow-band roofing filter affect receiver performance?
- E4C13 What is reciprocal mixing?
- E4C14 What is the purpose of the receiver IF Shift control?
E4D Receiver performance characteristics: dynamic range; intermodulation and cross-modulation interference; third-order intercept; desensitization; preselector; sensitivity; link margin
- E4D01 What is meant by the blocking dynamic range of a receiver?
- E4D02 Which of the following describes problems caused by poor dynamic range in a receiver?
- E4D03 What creates intermodulation interference between two repeaters in close proximity?
- E4D04 Which of the following is used to reduce or eliminate intermodulation interference in a repeater caused by a nearby transmitter?
- E4D06 What is the term for the reduction in receiver sensitivity caused by a strong signal near the received frequency?
- E4D07 Which of the following reduces the likelihood of receiver desensitization?
- E4D08 What causes intermodulation in an electronic circuit?
- E4D09 What is the purpose of the preselector in a communications receiver?
- E4D10 What does a third-order intercept level of 40 dBm mean with respect to receiver performance?
- E4D11 Why are odd-order intermodulation products, created within a receiver, of particular interest compared to other products?
- E4D12 What is the link margin in a system with a transmit power level of 10 W (+40 dBm), a system antenna gain of 10 dBi, a cable loss of 3 dB, a path loss of 136 dB, a receiver minimum discernable signal of -103 dBm, and a required signal-to-noise ratio of 6 dB?
- E4D13 What is the received signal level with a transmit power of 10 W (+40 dBm), a transmit antenna gain of 6 dBi, a receive antenna gain of 3 dBi, and a path loss of 100 dB?
- E4D14 What power level does a receiver minimum discernible signal of -100 dBm represent?
E4E Noise and interference: external RF interference; electrical and computer noise; line noise; DSP filtering and noise reduction; common-mode current; surge protectors; single point ground panel
- E4E01 What problem can occur when using an automatic notch filter (ANF) to remove interfering carriers while receiving CW signals?
- E4E02 Which of the following types of noise can often be reduced by a digital noise reduction?
- E4E03 Which of the following types of noise are removed by a noise blanker?
- E4E04 How can conducted noise from an automobile battery charging system be suppressed?
- E4E05 What is used to suppress radio frequency interference from a line-driven AC motor?
- E4E06 What type of electrical interference can be caused by computer network equipment?
- E4E07 Which of the following can cause shielded cables to radiate or receive interference?
- E4E08 What current flows equally on all conductors of an unshielded multiconductor cable?
- E4E09 What undesirable effect can occur when using a noise blanker?
- E4E10 Which of the following can create intermittent loud roaring or buzzing AC line interference?
- E4E11 What could be the cause of local AM broadcast band signals combining to generate spurious signals on the MF or HF bands?
- E4E12 What causes interference received as a series of carriers at regular intervals across a wide frequency range?
- E4E13 Where should a station AC surge protector be installed?
- E4E14 What is the purpose of a single point ground panel?
E5 Electrical Principles
E5A Resonance and Q: characteristics of resonant circuits; series and parallel resonance; definitions and effects of Q; half-power bandwidth
- E5A01 What can cause the voltage across reactances in a series RLC circuit to be higher than the voltage applied to the entire circuit?
- E5A02 What is the resonant frequency of an RLC circuit if R is 22 ohms, L is 50 microhenries, and C is 40 picofarads?
- E5A03 What is the magnitude of the impedance of a series RLC circuit at resonance?
- E5A04 What is the magnitude of the impedance of a parallel RLC circuit at resonance?
- E5A05 What is the result of increasing the Q of an impedance-matching circuit?
- E5A06 What is the magnitude of the circulating current within the components of a parallel LC circuit at resonance?
- E5A07 What is the magnitude of the current at the input of a parallel RLC circuit at resonance?
- E5A08 What is the phase relationship between the current through and the voltage across a series resonant circuit at resonance?
- E5A09 How is the Q of an RLC parallel resonant circuit calculated?
- E5A10 What is the resonant frequency of an RLC circuit if R is 33 ohms, L is 50 microhenries, and C is 10 picofarads?
- E5A11 What is the half-power bandwidth of a resonant circuit that has a resonant frequency of 7.1 MHz and a Q of 150?
- E5A12 What is the half-power bandwidth of a resonant circuit that has a resonant frequency of 3.7 MHz and a Q of 118?
- E5A13 What is an effect of increasing Q in a series resonant circuit?
E5B Time constants and phase relationships: RL and RC time constants; phase angle in reactive circuits and components; admittance and susceptance
- E5B01 What is the term for the time required for the capacitor in an RC circuit to be charged to 63.2% of the applied voltage or to discharge to 36.8% of its initial voltage?
- E5B02 What letter is commonly used to represent susceptance?
- E5B03 How is impedance in polar form converted to an equivalent admittance?
- E5B04 What is the time constant of a circuit having two 220-microfarad capacitors and two 1-megohm resistors, all in parallel?
- E5B05 What is the effect on the magnitude of pure reactance when it is converted to susceptance?
- E5B06 What is susceptance?
- E5B07 What is the phase angle between the voltage across and the current through a series RLC circuit if XC is 500 ohms, R is 1 kilohm, and XL is 250 ohms?
- E5B08 What is the phase angle between the voltage across and the current through a series RLC circuit if XC is 300 ohms, R is 100 ohms, and XL is 100 ohms?
- E5B09 What is the relationship between the AC current through a capacitor and the voltage across a capacitor?
- E5B10 What is the relationship between the AC current through an inductor and the voltage across an inductor?
- E5B11 What is the phase angle between the voltage across and the current through a series RLC circuit if XC is 25 ohms, R is 100 ohms, and XL is 75 ohms?
- E5B12 What is admittance?
E5C Coordinate systems and phasors in electronics: rectangular coordinates; polar coordinates; phasors; logarithmic axes
- E5C01 Which of the following represents pure capacitive reactance of 100 ohms in rectangular notation?
- E5C02 How are impedances described in polar coordinates?
- E5C03 Which of the following represents a pure inductive reactance in polar coordinates?
- E5C04 What type of Y-axis scale is most often used for graphs of circuit frequency response?
- E5C05 What kind of diagram is used to show the phase relationship between impedances at a given frequency?
- E5C06 What does the impedance 50 - j25 ohms represent?
- E5C07 Where is the impedance of a pure resistance plotted on rectangular coordinates?
- E5C08 What coordinate system is often used to display the phase angle of a circuit containing resistance, inductive, and/or capacitive reactance?
- E5C09 When using rectangular coordinates to graph the impedance of a circuit, what do the axes represent?
- E5C10 Which point on Figure E5-1 best represents the impedance of a series circuit consisting of a 400-ohm resistor and a 38-picofarad capacitor at 14 MHz?
- E5C11 Which point in Figure E5-1 best represents the impedance of a series circuit consisting of a 300-ohm resistor and an 18-microhenry inductor at 3.505 MHz?
- E5C12 Which point on Figure E5-1 best represents the impedance of a series circuit consisting of a 300-ohm resistor and a 19-picofarad capacitor at 21.200 MHz?
E5D RF effects in components and circuits: skin effect; real and reactive power; electrical length of conductors
- E5D01 What is the result of conductor skin effect?
- E5D02 Why is it important to keep lead lengths short for components used in circuits for VHF and above?
- E5D03 What is the phase relationship between current and voltage for reactive power?
- E5D04 Why are short connections used at microwave frequencies?
- E5D05 What parasitic characteristic causes electrolytic capacitors to be unsuitable for use at RF?
- E5D06 What parasitic characteristic creates an inductor’s self-resonance?
- E5D07 What combines to create the self-resonance of a component?
- E5D08 What is the primary cause of loss in film capacitors at RF?
- E5D09 What happens to reactive power in ideal inductors and capacitors?
- E5D10 As a conductor’s diameter increases, what is the effect on its electrical length?
- E5D11 How much real power is consumed in a circuit consisting of a 100-ohm resistor in series with a 100-ohm inductive reactance drawing 1 ampere?
- E5D12 What is reactive power?
E6 Circuit Components
E6A Semiconductor materials and devices: semiconductor materials; bipolar junction transistors; operation and types of field-effect transistors
- E6A01 In what application is gallium arsenide used as a semiconductor material?
- E6A02 Which of the following semiconductor materials contains excess free electrons?
- E6A03 Why does a PN-junction diode not conduct current when reverse biased?
- E6A04 What is the name given to an impurity atom that adds holes to a semiconductor crystal structure?
- E6A05 How does DC input impedance at the gate of a field-effect transistor (FET) compare with that of a bipolar transistor?
- E6A06 What is the beta of a bipolar junction transistor?
- E6A07 Which of the following indicates that a silicon NPN junction transistor is biased on?
- E6A08 What is the term for the frequency at which the grounded-base current gain of a bipolar junction transistor has decreased to 0.7 of the gain obtainable at 1 kHz?
- E6A09 What is a depletion-mode field-effect transistor (FET)?
- E6A10 In Figure E6-1, which is the schematic symbol for an N-channel dual-gate MOSFET?
- E6A11 In Figure E6-1, which is the schematic symbol for a P-channel junction FET?
- E6A12 What is the purpose of connecting Zener diodes between a MOSFET gate and its source or drain?
E6B Diodes
- E6B01 What is the most useful characteristic of a Zener diode?
- E6B02 Which characteristic of a Schottky diode makes it a better choice than a silicon junction diode for use as a power supply rectifier?
- E6B03 What property of an LED's semiconductor material determines its forward voltage drop?
- E6B04 What type of semiconductor device is designed for use as a voltage-controlled capacitor?
- E6B05 What characteristic of a PIN diode makes it useful as an RF switch?
- E6B06 Which of the following is a common use of a Schottky diode?
- E6B07 What causes a junction diode to fail from excessive current?
- E6B08 Which of the following is a Schottky barrier diode?
- E6B09 What is a common use for point-contact diodes?
- E6B10 In Figure E6-2, which is the schematic symbol for a Schottky diode?
- E6B11 What is used to control the attenuation of RF signals by a PIN diode?
E6C Digital ICs: families of digital ICs; gates; programmable logic devices
- E6C01 What is the function of hysteresis in a comparator?
- E6C02 What happens when the level of a comparator’s input signal crosses the threshold voltage?
- E6C03 What is tri-state logic?
- E6C04 Which of the following is an advantage of BiCMOS logic?
- E6C05 Which of the following digital logic families has the lowest power consumption?
- E6C06 Why do CMOS digital integrated circuits have high immunity to noise on the input signal or power supply?
- E6C07 What best describes a pull-up or pull-down resistor?
- E6C08 In Figure E6-3, which is the schematic symbol for a NAND gate?
- E6C09 What is used to design the configuration of a field-programmable gate array (FPGA)?
- E6C10 In Figure E6-3, which is the schematic symbol for a NOR gate?
- E6C11 In Figure E6-3, which is the schematic symbol for the NOT operation (inversion)?
E6D Inductors and piezoelectricity: permeability, core material and configuration; transformers; piezoelectric devices
- E6D01 What is piezoelectricity?
- E6D02 What is the equivalent circuit of a quartz crystal?
- E6D03 Which of the following is an aspect of the piezoelectric effect?
- E6D04 Why are cores of inductors and transformers sometimes constructed of thin layers?
- E6D05 How do ferrite and powdered iron compare for use in an inductor core?
- E6D06 What core material property determines the inductance of an inductor?
- E6D08 Which of the following materials has the highest temperature stability of its magnetic characteristics?
- E6D09 What devices are commonly used as VHF and UHF parasitic suppressors at the input and output terminals of a transistor HF amplifier?
- E6D10 What is a primary advantage of using a toroidal core instead of a solenoidal core in an inductor?
- E6D11 Which type of core material decreases inductance when inserted into a coil?
- E6D12 What causes inductor saturation?
E6E Semiconductor materials and packages for RF use
- E6E01 Why is gallium arsenide (GaAs) useful for semiconductor devices operating at UHF and higher frequencies?
- E6E02 Which of the following device packages is a through-hole type?
- E6E03 Which of the following materials supports the highest frequency of operation when used in MMICs?
- E6E04 Which is the most common input and output impedance of MMICs?
- E6E05 Which of the following noise figure values is typical of a low-noise UHF preamplifier?
- E6E06 What characteristics of MMICs make them a popular choice for VHF through microwave circuits?
- E6E07 What type of transmission line is often used for connections to MMICs?
- E6E08 How is power supplied to the most common type of MMIC?
- E6E09 Which of the following component package types have the least parasitic effects at frequencies above the HF range?
- E6E10 What advantage does surface-mount technology offer at RF compared to using through-hole components?
- E6E11 What is a characteristic of DIP packaging used for integrated circuits?
- E6E12 Why are DIP through-hole package ICs not typically used at UHF and higher frequencies?
E6F Electro-optical technology: photoconductivity; photovoltaic devices; optical sensors and encoders; optically isolated switching
- E6F01 What absorbs the energy from light falling on a photovoltaic cell?
- E6F02 What happens to photoconductive material when light shines on it?
- E6F03 What is the most common configuration of an optoisolator or optocoupler?
- E6F04 What is the photovoltaic effect?
- E6F05 Which of the following describes an optical shaft encoder?
- E6F06 Which of these materials is most commonly used to create photoconductive devices?
- E6F07 What is a solid-state relay?
- E6F08 Why are optoisolators often used in conjunction with solid-state circuits that control 120 VAC circuits?
- E6F09 What is the efficiency of a photovoltaic cell?
- E6F10 What is the most common material used in power-generating photovoltaic cells?
- E6F11 What is the approximate open-circuit voltage produced by a fully illuminated silicon photovoltaic cell?
E7 Practical Circuits
E7A Digital circuits: digital circuit principles and logic circuits; classes of logic elements; positive and negative logic; frequency dividers; truth tables
- E7A01 Which circuit is bistable?
- E7A02 What is the function of a decade counter?
- E7A03 Which of the following can divide the frequency of a pulse train by 2?
- E7A04 How many flip-flops are required to divide a signal frequency by 16?
- E7A05 Which of the following circuits continuously alternates between two states without an external clock signal?
- E7A06 What is a characteristic of a monostable multivibrator?
- E7A07 What logical operation does a NAND gate perform?
- E7A08 What logical operation does an OR gate perform?
- E7A09 What logical operation is performed by a two-input exclusive NOR gate?
- E7A10 What is a truth table?
- E7A11 What does “positive logic” mean in reference to logic devices?
E7B Amplifiers: class of operation; vacuum tube and solid-state circuits; distortion and intermodulation; spurious and parasitic suppression; switching-type amplifiers
- E7B01 For what portion of the signal cycle does each active element in a push-pull, Class AB amplifier conduct?
- E7B02 What is a Class D amplifier?
- E7B03 What circuit is required at the output of an RF switching amplifier?
- E7B04 What is the operating point of a Class A common emitter amplifier?
- E7B05 What can be done to prevent unwanted oscillations in an RF power amplifier?
- E7B06 What is a characteristic of a grounded-grid amplifier?
- E7B07 Which of the following is the likely result of using a Class C amplifier to amplify a single-sideband phone signal?
- E7B08 Why are switching amplifiers more efficient than linear amplifiers?
- E7B09 What is characteristic of an emitter follower (or common collector) amplifier?
- E7B10 In Figure E7-1, what is the purpose of R1 and R2?
- E7B11 In Figure E7-1, what is the purpose of R3?
- E7B12 What type of amplifier circuit is shown in Figure E7-1?
E7C Filters and matching networks: types of networks; types of filters; filter applications; filter characteristics; impedance matching
- E7C01 How are the capacitors and inductors of a low-pass filter Pi-network arranged between the network’s input and output?
- E7C02 What is the frequency response of a T-network with series capacitors and a shunt inductor?
- E7C03 What is the purpose of adding an inductor to a Pi-network to create a Pi-L-network?
- E7C04 How does an impedance-matching circuit transform a complex impedance to a resistive impedance?
- E7C05 Which filter type has ripple in the passband and a sharp cutoff?
- E7C06 What are the characteristics of an elliptical filter?
- E7C07 Which describes a Pi-L network?
- E7C08 Which of the following is most frequently used as a band-pass or notch filter in VHF and UHF transceivers?
- E7C09 What is a crystal lattice filter?
- E7C10 Which of the following filters is used in a 2-meter band repeater duplexer?
- E7C11 Which of the following measures a filter’s ability to reject signals in adjacent channels?
E7D Power supplies and voltage regulators; solar array charge controllers
- E7D01 How does a linear electronic voltage regulator work?
- E7D02 How does a switchmode voltage regulator work?
- E7D03 What device is used as a stable voltage reference?
- E7D04 Which of the following describes a three-terminal voltage regulator?
- E7D05 Which of the following types of linear voltage regulator operates by loading the unregulated voltage source?
- E7D06 What is the purpose of Q1 in the circuit shown in Figure E7-2?
- E7D07 What is the purpose of C2 in the circuit shown in Figure E7-2?
- E7D08 What type of circuit is shown in Figure E7-2?
- E7D09 How is battery operating time calculated?
- E7D10 Why is a switching type power supply less expensive and lighter than an equivalent linear power supply?
- E7D11 What is the purpose of an inverter connected to a solar panel output?
- E7D12 What is the dropout voltage of a linear voltage regulator?
- E7D13 Which of the following calculates power dissipated by a series linear voltage regulator?
- E7D14 What is the purpose of connecting equal-value resistors across power supply filter capacitors connected in series?
- E7D15 What is the purpose of a step-start circuit in a high-voltage power supply?
E7E Modulation and demodulation: reactance, phase, and balanced modulators; detectors; mixers
- E7E01 Which of the following can be used to generate FM phone signals?
- E7E02 What is the function of a reactance modulator?
- E7E03 What is a frequency discriminator?
- E7E04 What is one way to produce a single-sideband phone signal?
- E7E05 What is added to an FM speech channel to boost the higher audio frequencies?
- E7E06 Why is de-emphasis used in FM communications receivers?
- E7E07 What is meant by the term “baseband” in radio communications?
- E7E08 What are the principal frequencies that appear at the output of a mixer?
- E7E09 What occurs when the input signal levels to a mixer are too high?
- E7E10 How does a diode envelope detector function?
- E7E11 Which type of detector is used for demodulating SSB signals?
E7F Software defined radio fundamentals: digital signal processing (DSP) filtering, modulation, and demodulation; analog-digital conversion; digital filters
- E7F01 What is meant by “direct sampling” in software defined radios?
- E7F02 What kind of digital signal processing audio filter is used to remove unwanted noise from a received SSB signal?
- E7F03 What type of digital signal processing filter is used to generate an SSB signal?
- E7F04 Which method generates an SSB signal using digital signal processing?
- E7F05 How frequently must an analog signal be sampled to be accurately reproduced?
- E7F06 What is the minimum number of bits required to sample a signal with a range of 1 volt at a resolution of 1 millivolt?
- E7F07 What function is performed by a Fast Fourier Transform?
- E7F08 What is the function of decimation?
- E7F09 Why is an anti-aliasing filter required in a decimator?
- E7F10 What aspect of receiver analog-to-digital conversion determines the maximum receive bandwidth of a direct-sampling software defined radio (SDR)?
- E7F11 What sets the minimum detectable signal level for a direct-sampling software defined receiver in the absence of atmospheric or thermal noise?
- E7F12 Which of the following is generally true of Finite Impulse Response (FIR) filters?
- E7F13 What is the function of taps in a digital signal processing filter?
- E7F14 Which of the following would allow a digital signal processing filter to create a sharper filter response?
E7G Operational amplifiers: characteristics and applications
- E7G01 What is the typical output impedance of an op-amp?
- E7G02 What is the frequency response of the circuit in E7-3 if a capacitor is added across the feedback resistor?
- E7G03 What is the typical input impedance of an op-amp?
- E7G04 What is meant by the term “op-amp input offset voltage”?
- E7G05 How can unwanted ringing and audio instability be prevented in an op-amp audio filter?
- E7G06 What is the gain-bandwidth of an operational amplifier?
- E7G07 What voltage gain can be expected from the circuit in Figure E7-3 when R1 is 10 ohms and RF is 470 ohms?
- E7G08 How does the gain of an ideal operational amplifier vary with frequency?
- E7G09 What will be the output voltage of the circuit shown in Figure E7-3 if R1 is 1,000 ohms, RF is 10,000 ohms, and 0.23 volts DC is applied to the input?
- E7G10 What absolute voltage gain can be expected from the circuit in Figure E7-3 when R1 is 1,800 ohms and RF is 68 kilohms?
- E7G11 What absolute voltage gain can be expected from the circuit in Figure E7-3 when R1 is 3,300 ohms and RF is 47 kilohms?
- E7G12 What is an operational amplifier?
E7H Oscillators and signal sources: types of oscillators; synthesizers and phase-locked loops; direct digital synthesizers; stabilizing thermal drift; microphonics; high-accuracy oscillators
- E7H01 What are three common oscillator circuits?
- E7H02 What is a microphonic?
- E7H03 What is a phase-locked loop?
- E7H04 How is positive feedback supplied in a Colpitts oscillator?
- E7H05 How is positive feedback supplied in a Pierce oscillator?
- E7H06 Which of these functions can be performed by a phase-locked loop?
- E7H07 How can an oscillator’s microphonic responses be reduced?
- E7H08 Which of the following components can be used to reduce thermal drift in crystal oscillators?
- E7H09 What type of frequency synthesizer circuit uses a phase accumulator, lookup table, digital-to-analog converter, and a low-pass anti-alias filter?
- E7H10 What information is contained in the lookup table of a direct digital synthesizer (DDS)?
- E7H11 What are the major spectral impurity components of direct digital synthesizers?
- E7H12 Which of the following ensures that a crystal oscillator operates on the frequency specified by the crystal manufacturer?
- E7H13 Which of the following is a technique for providing highly accurate and stable oscillators needed for microwave transmission and reception?
E8 Signals and Emissions
E8A Fourier analysis; RMS measurements; average RF power and peak envelope power (PEP); analog/digital conversion
- E8A01 What technique shows that a square wave is made up of a sine wave and its odd harmonics?
- E8A02 Which of the following is a type of analog-to-digital conversion?
- E8A03 Which of the following describes a signal in the time domain?
- E8A04 What is “dither” with respect to analog-to-digital converters?
- E8A05 What is the benefit of making voltage measurements with a true-RMS calculating meter?
- E8A06 What is the approximate ratio of PEP-to-average power in an unprocessed single-sideband phone signal?
- E8A07 What determines the PEP-to-average power ratio of an unprocessed single-sideband phone signal?
- E8A08 Why are direct or flash conversion analog-to-digital converters used for a software defined radio?
- E8A09 How many different input levels can be encoded by an analog-to-digital converter with 8-bit resolution?
- E8A10 What is the purpose of a low-pass filter used at the output of a digital-to-analog converter?
- E8A11 Which of the following is a measure of the quality of an analog-to-digital converter?
E8B Modulation and demodulation: modulation methods; modulation index and deviation ratio; frequency- and time-division multiplexing; orthogonal frequency-division multiplexing (OFDM)
- E8B01 What is the modulation index of an FM signal?
- E8B02 How does the modulation index of a phase-modulated emission vary with RF carrier frequency?
- E8B03 What is the modulation index of an FM phone signal having a maximum frequency deviation of 3000 Hz either side of the carrier frequency if the highest modulating frequency is 1000 Hz?
- E8B04 What is the modulation index of an FM phone signal having a maximum carrier deviation of plus or minus 6 kHz if the highest modulating frequency is 2 kHz?
- E8B05 What is the deviation ratio of an FM phone signal having a maximum frequency swing of plus or minus 5 kHz if the highest modulation frequency is 3 kHz?
- E8B06 What is the deviation ratio of an FM phone signal having a maximum frequency swing of plus or minus 7.5 kHz if the highest modulation frequency is 3.5 kHz?
- E8B07 Orthogonal frequency-division multiplexing (OFDM) is a technique used for which types of amateur communication?
- E8B08 What describes orthogonal frequency-division multiplexing (OFDM)?
- E8B09 What is deviation ratio?
- E8B10 What is frequency division multiplexing (FDM)?
- E8B11 What is digital time division multiplexing?
E8C Digital signals: digital communication modes; information rate vs. bandwidth; error correction; constellation diagrams
- E8C01 What is Quadrature Amplitude Modulation or QAM?
- E8C02 What is the definition of symbol rate in a digital transmission?
- E8C03 Why should the phase of a PSK signal be changed at the zero crossing of the RF signal?
- E8C04 What technique minimizes the bandwidth of a PSK31 signal?
- E8C05 What is the approximate bandwidth of a 13-WPM International Morse Code transmission?
- E8C06 What is the bandwidth of an FT8 signal?
- E8C07 What is the bandwidth of a 4,800-Hz frequency shift, 9,600-baud ASCII FM transmission?
- E8C08 How does ARQ accomplish error correction?
- E8C09 Which digital code allows only one bit to change between sequential code values?
- E8C10 How can data rate be increased without increasing bandwidth?
- E8C11 What is the relationship between symbol rate and baud?
- E8C12 What factors affect the bandwidth of a transmitted CW signal?
- E8C13 What is described by the constellation diagram of a QAM or QPSK signal?
- E8C14 What type of addresses do nodes have in a mesh network?
- E8C15 What technique do individual nodes use to form a mesh network?
E8D Keying defects and overmodulation of digital signals; digital codes; spread spectrum
- E8D01 Why are received spread spectrum signals resistant to interference?
- E8D02 What spread spectrum communications technique uses a high-speed binary bit stream to shift the phase of an RF carrier?
- E8D03 Which describes spread spectrum frequency hopping?
- E8D04 What is the primary effect of extremely short rise or fall time on a CW signal?
- E8D05 What is the most common method of reducing key clicks?
- E8D06 What is the advantage of including parity bits in ASCII characters?
- E8D07 What is a common cause of overmodulation of AFSK signals?
- E8D08 What parameter evaluates distortion of an AFSK signal caused by excessive input audio levels?
- E8D09 What is considered an acceptable maximum IMD level for an idling PSK signal?
- E8D10 What are some of the differences between the Baudot digital code and ASCII?
- E8D11 What is one advantage of using ASCII code for data communications?
E9 Antennas and Transmission Lines
E9A Basic antenna parameters: radiation resistance, gain, beamwidth, efficiency; effective radiated power (ERP) and effective isotropic radiated power (EIRP)
- E9A01 What is an isotropic radiator?
- E9A02 What is the effective radiated power (ERP) of a repeater station with 150 watts transmitter power output, 2 dB feed line loss, 2.2 dB duplexer loss, and 7 dBd antenna gain?
- E9A03 What term describing total radiated power takes into account all gains and losses?
- E9A04 Which of the following factors affect the feed point impedance of an antenna?
- E9A05 What does the term “ground gain” mean?
- E9A06 What is the effective radiated power (ERP) of a repeater station with 200 watts transmitter power output, 4 dB feed line loss, 3.2 dB duplexer loss, 0.8 dB circulator loss, and 10 dBd antenna gain?
- E9A07 What is the effective isotropic radiated power (EIRP) of a repeater station with 200 watts transmitter power output, 2 dB feed line loss, 2.8 dB duplexer loss, 1.2 dB circulator loss, and 7 dBi antenna gain?
- E9A08 Which frequency band has the smallest first Fresnel zone?
- E9A09 What is antenna efficiency?
- E9A10 Which of the following improves the efficiency of a ground-mounted quarter-wave vertical antenna?
- E9A11 Which of the following determines ground losses for a ground-mounted vertical antenna operating on HF?
- E9A12 How much gain does an antenna have compared to a half-wavelength dipole if it has 6 dB gain over an isotropic radiator?
E9B Antenna patterns and designs: azimuth and elevation patterns; gain as a function of pattern; antenna modeling
- E9B01 What is the 3 dB beamwidth of the antenna radiation pattern shown in Figure E9-1?
- E9B02 What is the front-to-back ratio of the antenna radiation pattern shown in Figure E9-1?
- E9B03 What is the front-to-side ratio of the antenna radiation pattern shown in Figure E9-1?
- E9B04 What is the front-to-back ratio of the radiation pattern shown in Figure E9-2?
- E9B05 What type of antenna pattern is shown in Figure E9-2?
- E9B06 What is the elevation angle of peak response in the antenna radiation pattern shown in Figure E9-2?
- E9B07 What is the difference in radiated power between a lossless antenna with gain and an isotropic radiator driven by the same power?
- E9B08 What is the far field of an antenna?
- E9B09 What type of analysis is commonly used for modeling antennas?
- E9B10 What is the principle of a Method of Moments analysis?
- E9B11 What is a disadvantage of decreasing the number of wire segments in an antenna model below 10 segments per half-wavelength?
E9C Practical wire antennas; folded dipoles; phased arrays; effects of ground near antennas
- E9C01 What type of radiation pattern is created by two 1/4-wavelength vertical antennas spaced 1/2-wavelength apart and fed 180 degrees out of phase?
- E9C02 What type of radiation pattern is created by two 1/4-wavelength vertical antennas spaced 1/4-wavelength apart and fed 90 degrees out of phase?
- E9C03 What type of radiation pattern is created by two 1/4-wavelength vertical antennas spaced 1/2-wavelength apart and fed in phase?
- E9C04 What happens to the radiation pattern of an unterminated long wire antenna as the wire length is increased?
- E9C05 What is the purpose of feeding an off-center-fed dipole (OCFD) between the center and one end instead of at the midpoint?
- E9C06 What is the effect of adding a terminating resistor to a rhombic or long-wire antenna?
- E9C07 What is the approximate feed point impedance at the center of a two-wire half-wave folded dipole antenna?
- E9C08 What is a folded dipole antenna?
- E9C09 Which of the following describes a G5RV antenna?
- E9C10 Which of the following describes a Zepp antenna?
- E9C11 How is the far-field elevation pattern of a vertically polarized antenna affected by being mounted over seawater versus soil?
- E9C12 Which of the following describes an extended double Zepp antenna?
- E9C13 How does the radiation pattern of a horizontally polarized antenna vary with increasing height above ground?
- E9C14 How does the radiation pattern of a horizontally-polarized antenna mounted above a long slope compare with the same antenna mounted above flat ground?
E9D Yagi antennas; parabolic reflectors; feed point impedance and loading of electrically short antennas; antenna Q; RF grounding
- E9D01 How much does the gain of an ideal parabolic reflector antenna increase when the operating frequency is doubled?
- E9D02 How can two linearly polarized Yagi antennas be used to produce circular polarization?
- E9D03 What is the most efficient location for a loading coil on an electrically short whip?
- E9D04 Why should antenna loading coils have a high ratio of reactance to resistance?
- E9D05 Approximately how long is a Yagi’s driven element?
- E9D06 What happens to SWR bandwidth when one or more loading coils are used to resonate an electrically short antenna?
- E9D07 What is an advantage of top loading an electrically short HF vertical antenna?
- E9D08 What happens as the Q of an antenna increases?
- E9D09 What is the function of a loading coil in an electrically short antenna?
- E9D10 How does radiation resistance of a base-fed whip antenna change below its resonant frequency?
- E9D11 Why do most two-element Yagis with normal spacing have a reflector instead of a director?
- E9D12 What is the purpose of making a Yagi’s parasitic elements either longer or shorter than resonance?
E9E Impedance matching: matching antennas to feed lines; phasing lines; power dividers
- E9E01 Which matching system for Yagi antennas requires the driven element to be insulated from the boom?
- E9E02 What antenna matching system matches coaxial cable to an antenna by connecting the shield to the center of the antenna and the conductor a fraction of a wavelength to one side?
- E9E03 What matching system uses a short length of transmission line connected in parallel with the feed line at or near the feed point?
- E9E04 What is the purpose of the series capacitor in a gamma match?
- E9E05 What Yagi driven element feed point impedance is required to use a beta or hairpin matching system?
- E9E06 Which of these transmission line impedances would be suitable for constructing a quarter-wave Q-section for matching a 100-ohm feed point impedance to a 50-ohm transmission line?
- E9E07 What parameter describes the interaction of a load and transmission line?
- E9E08 What is a use for a Wilkinson divider?
- E9E09 Which of the following is used to shunt feed a grounded tower at its base?
- E9E11 What is the purpose of using multiple driven elements connected through phasing lines?
E9F Transmission lines: characteristics of open and shorted feed lines; coax versus open wire; velocity factor; electrical length; coaxial cable dielectrics; microstrip
- E9F01 What is the velocity factor of a transmission line?
- E9F02 Which of the following has the biggest effect on the velocity factor of a transmission line?
- E9F03 Why is the electrical length of a coaxial cable longer than its physical length?
- E9F04 What impedance does a 1/2-wavelength transmission line present to an RF generator when the line is shorted at the far end?
- E9F05 What is microstrip?
- E9F06 What is the approximate physical length of an air-insulated, parallel conductor transmission line that is electrically 1/2 wavelength long at 14.10 MHz?
- E9F07 How does parallel conductor transmission line compare to coaxial cable with a plastic dielectric?
- E9F08 Which of the following is a significant difference between foam dielectric coaxial cable and solid dielectric coaxial cable, assuming all other parameters are the same?
- E9F09 What impedance does a 1/4-wavelength transmission line present to an RF generator when the line is shorted at the far end?
- E9F10 What impedance does a 1/8-wavelength transmission line present to an RF generator when the line is shorted at the far end?
- E9F11 What impedance does a 1/8-wavelength transmission line present to an RF generator when the line is open at the far end?
- E9F12 What impedance does a 1/4-wavelength transmission line present to an RF generator when the line is open at the far end?
E9G The Smith chart
- E9G01 Which of the following can be calculated using a Smith chart?
- E9G02 What type of coordinate system is used in a Smith chart?
- E9G03 Which of the following is often determined using a Smith chart?
- E9G04 What are the two families of circles and arcs that make up a Smith chart?
- E9G05 Which of the following is a common use for a Smith chart?
- E9G06 On the Smith chart shown in Figure E9-3, what is the name for the large outer circle on which the reactance arcs terminate?
- E9G07 On the Smith chart shown in Figure E9-3, what is the only straight line shown?
- E9G08 How is a Smith chart normalized?
- E9G09 What third family of circles is often added to a Smith chart during the process of designing impedance matching networks?
- E9G10 What do the arcs on a Smith chart represent?
- E9G11 In what units are the wavelength scales on a Smith chart calibrated?
E9H Receiving antennas: radio direction finding (RDF) techniques; Beverage antennas; single- and multiple-turn loops
- E9H01 When constructing a Beverage antenna, which of the following factors should be included in the design to achieve good performance at the desired frequency?
- E9H02 Which is generally true for 160- and 80-meter receiving antennas?
- E9H03 What is receiving directivity factor (RDF)?
- E9H04 What is the purpose of placing an electrostatic shield around a small-loop direction-finding antenna?
- E9H05 What challenge is presented by a small wire-loop antenna for direction finding?
- E9H06 What indicates the correct value of terminating resistance for a Beverage antenna?
- E9H07 What is the function of a Beverage antenna’s termination resistor?
- E9H08 What is the function of a sense antenna?
- E9H09 What type of radiation pattern is created by a single-turn, terminated loop such as a pennant antenna?
- E9H10 How can the output voltage of a multiple-turn receiving loop antenna be increased?
- E9H11 What feature of a cardioid pattern antenna makes it useful for direction-finding antennas?
E0 Safety
E0A Safety: RF radiation hazards; hazardous materials; grounding
- E0A01 What is the primary function of an external earth connection or ground rod?
- E0A02 When evaluating RF exposure levels from your station at a neighbor’s home, what must you do?
- E0A03 Over what range of frequencies are the FCC human body RF exposure limits most restrictive?
- E0A04 When evaluating a site with multiple transmitters operating at the same time, the operators and licensees of which transmitters are responsible for mitigating over-exposure situations?
- E0A05 What hazard is created by operating at microwave frequencies?
- E0A06 Why are there separate electric (E) and magnetic (H) MPE limits at frequencies below 300 MHz?
- E0A07 What is meant by “100% tie-off” regarding tower safety?
- E0A08 What does SAR measure?
- E0A09 Which of the following types of equipment are exempt from RF exposure evaluations?
- E0A10 When must an RF exposure evaluation be performed on an amateur station operating on 80 meters?
- E0A11 To what should lanyards be attached while climbing?
- E0A12 Where should a shock-absorbing lanyard be attached to a tower when working above ground?